SCHEMATIC |
5 |
DESCRIPTION
RIGHT PANEL
The right hand side of the CS1000 contains the cable scanning SEND jacks. If you are connecting a cable with an unmatched amount of pins or electronic connections, plug the end with the MAXIMUM connections to this side.
The XLR jacks on this side are also used for the Phantom Power VOLTAGE test.
This side contains the following jacks:
1/4”,
LEFT PANEL
The left hand side of the CS1000 contains the cable scanning RECEIVE jacks in Cable Test Mode. In Test Tone mode, these jacks are the 1 kHz test tone OUTPUT jacks. The XLR jacks on this side are also used for the Phantom Power Present test.
The left panel contains the following jacks:
Banana, 1/4” TRS,
TOP PANEL
Battery 9 V: This is the cover for the 9 volt battery compart- | 1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| |
ment. |
|
|
| BATTERY 9 V |
|
|
|
| |
2+ | 3- |
|
|
| 3 |
|
| ||
Test Tone / Cable Test Switch: Selects the operating mode of |
| TEST | CABLE |
|
| ||||
1 | 2+ | TONE | OFF TEST | 2 |
|
| |||
2+ | 1 |
|
|
| pwr |
| 1 | 1 | |
the CS1000 - Cable Test, Test Tone, Phantom Power test, or | 3- | TONE OUTPUT SIDE |
|
|
| 2 | |||
|
|
|
| ||||||
4+ | + = positive polarity | 0 |
|
| 3 | ||||
- = negative polarity |
|
|
|
| |||||
| 1 = ground |
|
|
|
|
| 4 | ||
| 2+ |
|
| +3 |
|
| |||
OFF. |
|
|
|
|
| 2 |
| ||
1 | 1 |
|
|
|
|
|
| 1 | |
|
|
| +7 |
|
|
| |||
|
|
|
|
| 1 |
| |||
3- |
|
|
| TONE LEVEL |
| 3 | |||
|
|
|
|
| |||||
pwr LED: Indicates the CS1000 is in either Cable Test or Test | 2+ |
|
| (NOTE: Levels indicated are BALANCED. |
| 2 | |||
3- | For unbalanced levels, subtract 6 dB. ) |
| |||||||
| 2+ |
|
|
| 3 |
|
| ||
2+ | 1 |
|
|
|
|
| 2 | ||
|
|
|
| 2 |
| ||||
Tone mode. When this LED dims, battery replacement will be | 3- |
|
|
|
|
|
| 1 | 3 |
1 | MADE IN USA | PHANTOM POWER |
|
| 1 | ||||
|
|
| PRESENT |
|
|
| |||
|
|
|
|
|
|
|
| ||
necessary. | 1 | RECEIVE |
| SEND |
|
| 1 | ||
2+ |
| LINE |
| LINE |
|
|
| 2 | |
3- | 1 |
| 1 |
|
|
| 3 | ||
4+ |
|
|
|
| 4 | ||||
5 | 2 |
| 2 |
|
|
| 5 | ||
6 |
|
|
|
| 6 | ||||
Tone Level: Adjusts the level of the 1 kHz test tone. The levels | 7 | 3 |
| 3 |
|
|
| 7 | |
1 |
|
|
|
| 1 | ||||
4 | >52 | 4 |
|
|
| ||||
2+ |
|
|
| 2 | |||||
3- | 5 | >42 | 5 |
|
|
| 3 | ||
54+ |
|
|
| 54 | |||||
indicated by the knob are BALANCED levels. This means the | 6 | 6 | >32 | 6 |
|
|
| 6 | |
1 | 7 | >21 | 7 |
|
|
| 1 | ||
2+ |
|
|
| 2 | |||||
3- | 8 | >11 | 8 |
|
|
| 3 | ||
4+ |
|
|
| 4 | |||||
65 |
|
|
| PHANTOM POWER |
|
| 65 | ||
device being tested is receiving both positive and negative | 7 |
|
|
|
|
| 7 | ||
8 |
|
|
| VOLTAGE |
|
|
| 8 | |
|
|
|
|
|
|
|
|
| |
polarity signals. If you are testing an unbalanced device, with |
|
|
|
|
|
|
|
|
|
only the positive signal and ground, divide the amount shown in half. |
|
|
|
|
|
| |||
Signal LEDs: These 16 LEDs (8 on the Send side, 8 Receive) indicate several |
|
| |||||||
things: |
|
|
|
|
|
|
|
|
|
•In Cable Test mode the lit LED on the SEND side indicates a signal being sent on corresponding pin number, on the RECEIVE side the lit LED indicates which pin that signal is being received on.
•When testing Phantom Power Voltage, the bottom five LEDs on the SEND side will indicate the Phantom Power voltage.
•When testing Phantom Power Presence, LEDs number two and three on the RECEIVE side will light if voltage is present on both pins.
2