Panasonic NV-VHD1EC Setting up, Automatic Setting without Q Link, Automatic Setting with Q Link

AC IN~

VCR / DVD		Aerial
		(not supplied)
AV1	RF IN	TV
		(not supplied)
	RF OUT

RF coaxial lead (supplied)

21-pin scart lead

(not supplied)

On Screen Display

Country	Panasonic	VCR
Belgien
	Deutschland
Belgique	Österreich
Belgiê	Portugal
Clock setting	Panasonic	VCR

Clock setting : MAN.

Time : 20:30:24

Date : 21.03.01

Setting up

Set up the connections shown here and connect the mains lead (supplied) to your AC IN.  The RF (radio frequency) coaxial lead must be connected for TV reception,

even if the video recorder is already connected with a 21-pin scart lead.

For more information about the remote control buttons and cursors see pages 4-5.

Automatic Setting without Q Link		AC mains lead
	Set the remote control to VCR
		(supplied)
	Switch on the unit and the [Country] setting menu will appear.
	Use the cursors on the remote control to select your country.
	After pressing ENTER, all the TV stations which can be received will be tuned automatically in about 5 minutes.
	If the menu [Clock setting] appears, use the cursors or the numeric buttons
	on the remote control to set the Time and Date manually.
	To end this procedure, press ENTER.
	To cancel this settings press EXIT.

Note: If the selection for the Country menu does not appear after switching on the unit, you can restart the automatic setting; see page 10. An incorrect setting of time or date (observe summer- and wintertime) will influence the timer recording.

Automatic Setting with Q Link

Download

Panasonic VCR

If your TV is equipped with Q Link or with a similar function from other manufacturers (see note), the TV programme positions can be downloaded with a fully-wired 21-pin scart lead (not supplied).

Download in progress, please wait.

Position 49

VCR display

The programme positions must be tuned on the TV first.  Connect the scart lead.

 Set the AV channel of the TV.

 Set the remote control to VCR .  Switch on the unit .

 Downloading of the TV data starts.

 When the channel indication stops flashing on the VCR display, the downloading is complete.

Note about R: The following systems from other manufacturers have a similar function to Q Link from

Panasonic. List of registered trademarks: Q Link (Panasonic), DATA LOGIC (Metz), Easy Link (Philips), Megalogic (Grundig), SMARTLINK (Sony)

Main menu

Panasonic VCR

Manual download start

 Set the AV channel of the TV.

Timer recording Tuning

Clock setting Other settings

	Set the remote control to VCR	.
	Press MENU
	Select [Tuning] 


Tuning

Panasonic VCR

	Access by pressing ENTER
	Select [Download]

Manual

Auto-Setup Restart

Download

Shipping condition

VCR / DVD

TV

RF Coaxial lead (supplied)

VCR display

On Screen Display

VCR

Ch:36

RQTD0035-A

	Press ENTER
	Confirm by pressing ENTER
	When the channel indication stops flashing on the VCR display, the downloading is complete.

Connect the TV only with a RF coaxial lead

You must ensure that the video output channel is adjusted to the input channel of the TV. Please also read the operating instructions for your TV.

	Set the remote control to VCR	.
	Switch on the unit
	Press MENU for about 7 seconds until the number of the channel appears
	on the VCR display. The pre-setting is channel 36 (NV-VHD1 EC) 38 (NV-VHD1 EE).
	Tune the TV until the test screen appears. A distorted picture on the channel can be reduced
	by adjusting the unit and the TV to another channel.
	Use the CH button or the numeric buttons to select the channel number (e.g. channel 39).
	Tune the TV until the test screen appears.
	To store this adjustment, press ENTER .
	After that, please continue with the Automatic Setting with the [Country] setting menu.		3