FUNAI MFV210C warranty Troubleshooting Guide, Specifications, Maintenance

Page 6

TROUBLESHOOTING GUIDE

If you have followed the instructions contained in this manual and have difficulty in operating your VCP, locate the PROBLEM in the left column below. Check the corresponding CORRECTIVE ACTION column to remedy the problem.

PROBLEM

CORRECTIVE ACTION

 

 

No power.

• Make sure the power plug is connected to an AC outlet.

 

• Make sure the DC cord is connected to a 13.2 VOLT (12V) DC cigarette lighter socket.

 

Check the fuse on the DC cord.

 

• Make sure the power is turned on.

Playback picture is partially noisy.

• Adjust tracking control for a better picture by pressing [TRACKING o/p].

Cannot view a tape but the

• Head cleaning may be necessary. Refer to “AUTO HEAD CLEANING” .

audio is OK.

• Make sure the VCP is not in the Menu mode.

No or poor playback picture.

• Fine tune your TV.

TV programs cannot be seen

Re-check the ANT. IN and ANT. OUT connections.

normally.

• Turn off the VCP.

No VCP operation from the

• Make sure the power plug is connected to an AC outlet.

infrared Remote Control.

• Make sure the DC cord is connected to a 13.2 VOLT (12V) DC cigarette lighter socket.

 

Check the fuse on the DC cord.

 

• Check batteries in remote control.

Noise in picture on playback.

• Head cleaning is necessary. Refer to “AUTO HEAD CLEANING”.

SPECIFICATIONS

Operating temperature :

5°C~40°C (41°F~104°F)

Power requirement :

AC120V, 60Hz

DC13.2V (12V)

Converter output :

VHF Channel 3 or 4.

Power consumption :

AC12W

DC10W

 

 

Dimensions :

W 11” (280mm)

 

 

 

 

H 3-5/8” (92mm)

 

• Designs and specifications are subject to change

 

D 9-13/16” (250mm)

Weight :

4.4 lbs. (2.0 Kg.) (approx.)

without notice.

 

 

 

 

• If there is a discrepancy

between languages, the

 

 

 

MAINTENANCE

TROUBLESHOOTING SPECIFICATIONS MAINTENANCE GUIDE

SERVICING

Should your VCP become inoperative, do not try to correct the problem by yourself. There are no user-serviceable parts inside. Turn off, unplug the power plug, and please call our help line at

1-800-242-7158,

to locate an Authorized Service Center.

CABINET CLEANING

Wipe the front panel and other exterior surfaces of the VCP with a soft cloth immersed in lukewarm water and wrung dry.

Never use a solvent or alcohol. Do not spray insecticide liquid near the VCP. Such chemicals may cause damage and discoloration to the exposed surfaces.

AUTO HEAD CLEANING

Automatically cleans video heads as you insert or remove a cassette, so you can see a clear picture.

Playback picture may become blurred or interrupted while the TV program reception is clear. Dirt accumulated on the video heads after long periods of use, or the usage of rental or worn tapes can cause this problem. If a streaky or snowy picture appears during playback, the video heads in your VCP may need to be cleaned.

1.Please visit your local Audio/Video store and purchase a good quality VHS Video Head Cleaner.

2.If a Video Head Cleaner does not solve the problem, please call our help line at 1-800-242-7158, to locate an Authorized Service Center.

NOTES:

Remember to read the instructions included with the video head cleaner before use.

Clean video heads only when problems occur.

– 6 –

EN

Image 6
Contents Description Controls SafeguardsWarranty Status DisplayPrecautions Install LocationDisplay Description of ControlsCheck contents Preparation for USEPlayback Function Auto Repeat PlaybackTroubleshooting Guide SpecificationsMaintenance Panel frontal Limits and Exclusions Exchange DurationRepair Duration Funai Corporation