GoVideo DVR1000 manual Instant Timer Recording, Checking the Recording Time, Ing time length

ote

When you stop DVD playback during copying, the VCR Recording mode also stops automatically.

When the DVD is finished playing, press STOP (x) to stop recording.

You must stop the Copy process manually when the DVD movie ends, or the unit may replay and record over and over again.

5

The DVD+VCR will go into Record mode. The “COPY” indicator will light.

Stop the Copy Process

4

If the DVD disc menu appears, you may need to press PLAY (N) manually to begin copying.

Press COPY on the front panel.

The DVD will go into Play mode

Press PLAY (N) on the DVD deck.

Insert VHS Tape

2 Insert a blank VHS video tape into the VCR deck.

3

ote

Before recording, please confirm the recording start position.

Copying from DVD to VCR

This unit is capable of copying the contents of a DVD to a VHS tape.

ote

If the DVD you are attempting to copy is copy protected, you will not be able to copy the disc. It is not permitted to copy Macrovision-encoded DVDs. “Lock” is displayed on the front panel display.

Insert Disc

1 Insert the disc you wish to copy in the DVD deck and close the disc tray.

4

When you are ready to begin recording, press REC (z) once to start.

Dubbing and Editing

You can easily edit or dub camcorder/VCR recordings to the DVD+VCR via the front/rear panel audio/video jacks. These direct A/V jacks provide better picture results than using the RF jack on the rear panel.

Connect the camcorder (or secondary VCR) to the

1 A/V inputs of the DVD+VCR as shown on page 13.

Set the input channel to “AV”. (Press INPUT to

2 select AV.)

If you have connected your DVD+VCR to the A/V input jacks on the rear of the DVD+VCR, you should select AV by pressing INPUT.

Play the tape in the camcorder (or another

3 VCR). If you have a TV attached to your DVD+VCR, you can see the video playing.

VCR Operation (Continued)

Instant Timer Recording

Instant Timer Recording allows you to easily make a recording of a preset length without using the program- mable timer.

Preparation:

Turn on the power on both the DVD+VCR and the TV.

Be sure the TV is tuned to the DVD+VCR output channel (3 or 4). If a direct VIDEO/AUDIO connection is made between the DVD+VCR and the TV, set the TV’s source selector to VIDEO.

1

2

Insert a video cassette with the record safety tab intact.

Select the desired channel with v/V or the num- ber (0-9) buttons.

The channel number appears on the TV screen.

If you are recording from another source via the audio/video input jacks (on the Rear), select AV.

3 Select the desired recording speed (SP or SLP) with the SP/SLP button.

The tape speed will appear on the TV screen.

4The “Instant Timer Record” will appear on the TV screen.

Recording will start. (The indicator will light)Press REC (z) twice.

5ing time length.

At the end of the recording, the DVD+VCR will stop recording and shut off.

During Instant Timer Recording, you cannot change the

channel on the DVD+VCR.

You can stop the recording by pressing STOP (x).Press REC (z) repeatedly to select the record-

INSTANT TIMER RECORD MENU

INSTANT TIMER RECORD		0H30M ..... 9H00M ➝ 0H00M
CHANNEL	2
			Length Display
SPEED	SP
		(each additional press of
START	NOW	REC (z) increases recording
LENGTH	0H30M		time 30 minutes)

Checking the Recording Time

Press REC (z) once to check the recording time. The DVD+VCR will display the time on screen for ~6 sec- onds and then return to the recording in progress.

To Extend the Recording Time

Recording time can be extended anytime by pressing REC (z).

Subsequent presses result in increasing the recording time in 30-minute increments.

otes

If you press PAUSE/STEP (X) during instant timer record- ing, the DVD+VCR will enter Record/Pause mode. Instant Timer Recording is cancelled.

If the DVD+VCR is set to “0H00M”, the DVD+VCR goes to normal Recording mode.

24