JVC HR-J491MS, LPT0684-001A When this function is set to on, When this function is set to OFF

Page 10

– Other Functions –

B.E.S.T. — ON / OFF

When B.E.S.T. (Biconditional Equalized Signal Tracking) system is set to “ON”, this recorder checks the condition of the tape in use during playback and recording, and compensates to provide the highest-possible pictures. This takes place whenever you play back a tape or start recording after inserting a tape.

NOTE:

The recorder checks the tape condition for about 7 seconds, then starts recording. To make sure you record the desired scene or program completely, perform the following steps:

APress and hold PAUSE (9), and press REC (7). After about 7 seconds, the recorder re-enters Record Pause mode.

BPress PLAY (4) to start recording.

PICTURE CONTROL — AUTO(NORM) / EDIT / SOFT / SHARP

This function helps you to adjust the playback picture quality according to your preference.

AUTO (NORM): Normally select this. Picture quality is adjusted automatically. When “B.E.S.T.” is “OFF”, “NORM” will appear instead of “AUTO”.

EDIT: Minimizes picture degradation during editing (recording and playback).

SOFT: Reduces image coarseness when viewing overplayed tapes containing much noise.

SHARP: Clearer, sharper-edged picture when viewing images with much flat, same-coloured surfaces such as cartoons.

NOTE:

Select “EDIT” when you are editing tapes. After you finish editing the tapes, select “AUTO”.

PAL/MESECAM — AUTO / PAL / MESECAM

Select the appropriate colour system for recording or playback. AUTO: Usually set to this mode. The appropriate colour system (PAL or MESECAM) will be selected depending on the playback or recording signals.

If the “AUTO” mode does not work properly, select either of the following manual modes.

PAL: To record PAL signals, or playback a PAL tape.

MESECAM: To record SECAM signals, or playback a SECAM or MESECAM tape.

NOTES:

●SECAM signals will always be recorded as MESECAM. Select “AUTO” or “MESECAM” when recording SECAM signals.

●When playing back a SECAM tape, select “AUTO” or “MESECAM”. The playback picture will always be monochrome.

NTSC — NTSC3.58 / NTSC4.43 / NTSC]PAL

To record NTSC signals or playback a NTSC tape, it will be necessary to select the appropriate mode.

NTSC3.58: To record NTSC signals or playback a NTSC tape.

NTSC4.43: To record NTSC4.43 signals or playback a NTSC4.43 tape.

NTSC]PAL: To playback a NTSC tape on PAL TV.

NOTE:

●The “NTSC]PAL” mode does not work during recording. In this mode, NTSC signals will be recorded as NTSC3.58.

●The Menu screen is distorted during playing back a NTSC tape on PAL TV. Stop playback and access the Menu screen again.

●In the “NTSC4.43” mode, with some TVs, on-screen displays (Program screen, etc.) may roll up or down and there may be a loss of colour. When this happens, select the “NTSC3.58” mode.

AUTO TIMER — ON / OFF

●When this function is set to “ON”:

The timer recording standby mode is automatically engaged when the recorder is turned off. It is temporarily canceled when the recorder is turned on.You do not have to press # to engage or disengage the timer recording standby mode.

●When this function is set to “OFF”:

You have to press # to engage or disengage the timer recording standby mode.

O.S.D. — ON / OFF

When this function is set to “ON”, various recorder status information (on-screen display) appears on the screen.

NOTE:

When you use this recorder as the source player for editing a tape, be sure to set this function to “OFF”; otherwise, the recorder status information (on-screen display) will be recorded on the edited tape.

AUTO SP]LP TIMER — ON / OFF

When this function is set to “ON”, the recorder automatically switches to LP mode to allow complete recording if there is not enough tape to record the entire program while timer-recording in SP mode.

For Example, Recording a PAL-broadcast programme of 210 minutes in length onto a 180-minute tape.

Approximately 150 minutes

Approximately 60 minutes

SP mode

LP mode

 

 

Total 210 minutes

NOTES:

●If you have programed the recorder to timer-record 2 or more programs, do not use this function, but change the tape speed manually during timer programing.

●There may be some noise and sound disturbance where the tape speed switches from SP to LP mode on the tape.

●The Auto SP]LP Timer feature is not available during ITR (Instant Timer Recording), and the feature will not work properly with any tapes longer than E-180 or with some tapes of shorter lengths.

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Safety Precautions HR-J491MSFront Panel How to use the remote controlVideo heads cleaning Rear PanelOn-screen display Remote controlBasic Connections RF ConnectionInstalling/Removing the lithium battery Initial SettingsAuto Set Up Video Channel SetPlayback Clock SettingBasic Playback Playback Features Recording Recording FeaturesSpecifying recording length Instant Timer Recording ITR Basic RecordingTimer Recording Express Timer ProgramingOther Functions Function settingsChecking tape position When this function is set to on When this function is set to OFFMulti-Brand Remote Control TV Brand SettingTo control two recorders with the same remote control EditingPlayback Information on Multi-System CompatibilityOff-Air Recording Recorded tapeAuto Channel Set Tuner SettingTape-To-Tape Editing Manual Channel SetDelete a Channel Fine-Tuning ChannelsSwap Channel Positions Specifications General

LPT0684-001A, HR-J491MS specifications

The JVC HR-J491MS, identified by the model number LPT0684-001A, is a VCR that encapsulates the essence of vintage video technology, showcasing the brand's dedication to quality and user-friendly design. Released during the height of the VHS format's popularity, this model is often recognized for its robust performance and compatibility features that cater to a variety of user needs.

One of the standout features of the HR-J491MS is its excellent tape handling capabilities. The model is equipped with JVC's proprietary Super VHS technology, which enhances video playback quality. Super VHS allows for higher resolution recordings compared to standard VHS, delivering sharper images and more vivid colors. This is particularly appealing for users looking to archive home videos or watch classic films with improved clarity.

Another important characteristic of the HR-J491MS is its built-in timer recording feature. This allows users to schedule recordings well in advance, ensuring that they never miss their favorite programs. The intuitive interface makes setting up recordings straightforward, with options to specify date, time, and duration easily.

The design of the HR-J491MS supports a variety of media formats, allowing users to play both standard VHS tapes and Super VHS tapes. This versatility means that it can serve as a reliable choice for those with a substantial collection of video media from different eras. Its compatibility with various tape formats ensures that it remains functional for a broad user base.

The VCR also integrates noise reduction technologies that help minimize video and audio artifacts during playback. This feature enhances the overall viewing experience, particularly for older or more worn tapes, ensuring that users enjoy a cleaner, more enjoyable playback.

Moreover, the JVC HR-J491MS is equipped with multiple connectivity options, including composite and RF outputs. This makes it easy to connect to a range of televisions and audio systems, allowing users to enjoy their videos on different setups without hassle.

In summary, the JVC HR-J491MS, LPT0684-001A, is a remarkable piece of vintage technology that balances functionality and quality. With features like Super VHS compatibility, timer recording, and noise reduction, it stands out as an excellent choice for both collectors and casual users looking to relive their video memories.
Top Page Image Contents