JVC HR-VP790U manual Multi-Brand Remote Control, Changing Remote Control Code, TV Brand Setting

Page 13

– Other Functions –

Multi-Brand Remote Control

This Remote can control some functions of remote controllable TVs, cable boxes or DBS (Direct Broadcast Satellite) receivers listed below. Without setting, you can control a JVC TV.

NOTES:

●Some unit’s brands have more than one code. If the unit does not function with a specified code, try other codes.

●Depending on the type of unit, some or all functions cannot be operated using this Remote.

●It’s not possible to operate a unit not equipped with a remote sensor.

●It’s not possible to set the Remote for both your cable box and a DBS receiver at the same time.

●Once you have set the Remote to operate the unit, you do not have to set it until you replace the batteries from the Remote.

TV Brand Setting

ATurn on TV

Turn on the TV using the Power button on the TV or its Remote.

BSet TV brand code

APress and hold TV.

BPress MBR SET.

CPress the Number keys to enter your TV’s brand code.

DPress OK, and release TV. The TV should turn off.

COperate TV

While holding down TV, press one of the following buttons: POWER, TV/VCR, TV CH+/–, ^(TV Muting), TV VOL+/–, and the Number keys.

●For some brands, you must press ENTER after having pressed the Number keys to enter a channel number.

TV BRAND

CODE

TV BRAND

CODE

 

 

 

 

JVC

01, 03

SONY

07

HITACHI

10

SAMSUNG

12

MAGNAVOX

02

SANYO

13

MITSUBISHI

03

SEARS

13

PANASONIC

04, 11

TOSHIBA

08

RCA

05

ZENITH

09

SHARP

06

 

 

 

 

 

 

Cable Box or DBS Receiver Brand Setting

ATurn on cable box or DBS receiver

Turn on the cable box or DBS receiver using the Power button on the unit or its Remote.

BEnter brand code

APress and hold CABLE/DBS.

BPress MBR SET.

CPress the Number keys to enter your cable box’s (or DBS receiver’s) brand code.

DPress OK, and release CABLE/DBS.

COperate cable box or DBS receiver

While holding down CABLE/DBS, press one of the following buttons: POWER, TV CH+/–, and the Number keys.

●For some brands, you must press ENTER after having pressed the Number keys to enter a channel number.

●To change the cable box’s (or DBS receiver’s) channels, press TV CH+/– or the Number keys. (The CH+/– button can be used to change the VCR’s channels only.)

CABLE BOX BRAND

CODE

 

 

ARCHER

01, 05, 17

CABLETENNA

01, 17

CABLEVIEW

15, 16, 17, 21, 25

CITIZEN

15, 16, 17, 21, 25

CURTIS

02

DIAMOND

01, 17

EASTERN

19

GC BRAND

15, 16, 17, 21, 25

GEMINI

15

GENERAL INSTRUMENTS

01, 04, 06, 11, 12, 15, 28

HAMLIN

10, 18, 19, 23

JASCO

15

JERROLD

01, 04, 06, 11, 12, 15, 28

NOVAVISION

02

OAK

07

PANASONIC

13, 14

PULSER

15, 16, 17, 21, 25

RCA

13, 14

REGAL

10, 18, 19, 23

REGENCY

19

REMBRANDT

01, 16, 17

SAMSUNG

05, 16, 24

SCIENTIFIC ATLANTA

02

SIGMA

07

SL MARX

05, 16, 17, 24, 25

SPRUCER

13, 14

STARGATE

05, 15, 16, 17, 21, 24, 25

TELEVIEW

05, 16, 24

TOCOM

01, 04, 16

UNIKA

01, 17

UNIVERSAL

16, 17, 25

VIDEOWAY

03, 09, 22

ZENITH

03, 09, 22

 

 

DBS RECEIVER BRAND

CODE

 

 

JVC (DISH Network)

51

ECHOSTAR (DISH Network)

51

PRIMESTAR

50

SONY (DSS)

41

RCA (DSS)

40

 

 

Changing Remote Control Code

This Remote is capable of transmitting two control codes; one set to respond to A code control signals and another set to respond to B code control signals. This Remote control is preset to send A code signals because your VCR is initially set to respond to A code signals. You can easily modify your VCR and the Remote to respond to B code signals. When using two JVC VCRs, set two VCRs and their Remotes to different codes, so that you can operate these VCRs separately.

ASet remote control code for Remote

APress and hold A/B.

BPress the Number key “2”.

CPress OK, and release A/B.

●The Remote now can transmit B code control signals.

BCheck remote control code for VCR

Press and hold 4 on the VCR for more than 5 seconds while the VCR is turned off. The code currently set appears on the display panel.

CChange code for VCR

Press any key on the Remote. The VCR now responds to B code control signals.

●To set the Remote and the VCR back to A code control signals, repeat the same procedure as shown above except pressing the Number key “1” in step B of 1.

To control two VCRs with the same Remote

You can control two JVC VCRs by switching the remote control code for the Remote between A and B ( step A), keeping two VCRs to different control codes.

●To change only the remote control code for the Remote, DO NOT perform steps B and C.

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Model Number HR-VP790U Trade Name Dear CustomerResponsible Party JVC Americas Corp Address Telephone NumberPower Cord Protection Power SourcesAccessories CleaningRear Panel Buttons, Connectors and IndicatorsRemote Front PanelInitial Settings Connections and Plug&Play SettingLanguage Setting RF ConnectionTuner Setting Clock SettingSetting channels manually Manual Channel Set Cable Box and/or DBS Receiver Control SettingBasic Playback PlaybackLoad a cassette Start playbackPlayback Features Recording Features Timer RecordingChanging VCR Plus+ Setting RecordingExpress Timer Programing VCR Plus+ Timer ProgramingTo use the VCR while it is in timer recording standby mode 24HR Quick ProgramingFunction settings Timer warning displayOther Functions Checking tape positionSatellite Auto Recording EP modeChanging Remote Control Code Multi-Brand Remote ControlTV Brand Setting Cable Box or DBS Receiver Brand SettingEditing SpecificationsFor Servicing Only in U.S.A HOW to Locate Your JVC Service CenterLimited Warranty Warranty Only in U.S.A

HR-VP790U specifications

The JVC HR-VP790U is a sophisticated VCR that showcases JVC's renowned expertise in the field of video technology. As a versatile VCR, it combines high-quality video playback and recording capabilities, making it a desirable choice for both casual viewers and video enthusiasts alike.

One of the standout features of the HR-VP790U is its ability to support VHS, S-VHS, and S-VHS ET formats. This flexibility allows users to enjoy a wide range of video content, whether it comes from standard VHS tapes or high-resolution S-VHS tapes. The incorporation of the S-VHS ET technology enhances the video output quality of standard VHS tapes, enabling users to experience sharper and clearer images compared to traditional VHS playback.

The HR-VP790U is equipped with JVC's advanced digital noise reduction technology, which minimizes visual artifacts and enhances the overall picture quality. This technology is particularly beneficial for users who often deal with older tapes that may have suffered from degradation over time. Additionally, the VCR features various playback modes, including slow motion and frame-by-frame playback, which add to the viewing experience by allowing users to engage with the content more intimately.

Another significant characteristic of the HR-VP790U is its robust recording capabilities. The unit features a one-touch recording function that simplifies the process of capturing video content onto tape. Users can easily set the timer recording functions to ensure they never miss their favorite shows. This feature is especially useful for those with busy schedules who want to keep up with television programming.

In terms of connectivity, the HR-VP790U boasts composite video and audio outputs, making it compatible with a wide variety of televisions and other multimedia devices. Additionally, the unit provides a simple and intuitive interface, allowing users to navigate through menus and settings with ease.

Overall, the JVC HR-VP790U is a well-rounded VCR that combines quality, versatility, and ease of use. Whether you are reliving memories from your VHS collection or recording new content, this model delivers impressive performance tailored to meet the needs of modern users while honoring the legacy of traditional video technology. Its combination of advanced features and user-friendly design makes it a remarkable choice for home entertainment enthusiasts.
Top Page Image Contents