JVC HR-VP793U manual Timer Recording, Basic Recording, Recording Features

Recording

It may be unlawful to record or play back copyrighted material without the consent of the copyright owner.

Accidental erasure prevention

To prevent accidental recording on a
recorded cassette, remove its record
safety tab. To record on it later, cover
the hole with adhesive tape.	Record safety tab

Basic Recording

ALoad a cassette

Make sure the record safety tab is intact. If not, cover the hole with adhesive tape before inserting the cassette.

●The VCR turns on, and the counter is reset, automatically.

BSelect recording channel

Press CH+/– or the Number keys on the Remote [CH+/– on the VCR]. Or push the JOG dial, then turn it to the left or right.

●If you connect the TV and the VCR only using the RF connection, press TV/VCR on the Remote so that the VCR mode indicator lights on the display panel, to view the program to be recorded.

CSet tape speed

Press SP/EP.

DStart recording

On the VCR, press REC (7). Or on the Remote, while holding REC (7), press PLAY (4).

NOTE:

If “VIDEO CALIBRATION” is set to “ON” (default setting), the VCR takes about 7 seconds to assess the quality of the tape in use, then recording begins with the picture level optimized.

During recording

Pause recording

Press PAUSE (9).

●Press PLAY (4) to resume recording.

●You can select channel in the recording pause mode.

Stop recording

Press STOP (8) on the	OR Press STOP/EJECT (0) on
Remote.	the VCR.

Recording Features

Specifying recording length

— Instant Timer Recording (ITR)

During recording, press REC (7) on the VCR repeatedly until the recording length you want appears on the display panel. The record indicator () on the display panel starts blinking.

●Each time you press the button, recording length increases in 30-minute intervals (up to 6 hours).

●The VCR shuts off after recording is finished.

●To cancel an ITR, press STOP (8) on the Remote or STOP/EJECT (0) on the VCR.

Watching one program while recording another

During recording...

●If you connect the TV and the VCR only using the RF connection to view pictures from the VCR, press TV/VCR on the Remote so that VCR mode indicator goes off from the display panel. (The TV broadcast being recorded disappears.)

●If you are using the AV connection to view pictures from the VCR, change the TV’s input mode from AV to TV.

Then, select the channel you want to watch, on the TV.

Second Audio Recording

This VCR’s built-in MTS decoder enables reception of Multichannel TV Sound broadcast. To record a SAP program received, set “2ND AUDIO RECORD” to “ON”.

Timer Recording

Up to 8 timer recording programs can be made using VCR Plus+ timer programing, Express timer programing or 24HR Quick Programming method as far as a year in advance. Remember, the clock must be set before you can program the timer.

NOTES:

●If all the 8 programs have already been set, “PROGRAM FULL” or “Full” appears on the TV screen or the display panel.

●After timer recording is completed, the VCR turns off automatically.

●You can program the timer recording while a regular recording is in progress; the menu screens will not be recorded.

●To timer-record cable or satellite channels, perform “Cable Box and/or DBS Receiver Control Setting” and be sure to keep the cable box or DBS receiver turned on.

●Even if a power failure occurs, the VCR keeps your timer programs. However, the clock time, channel settings, and other menu settings are lost. As a result, when the power is supplied again to this VCR after the power failure, this VCR starts the Plug&Play setting automatically to restore the clock time and channel setting. If the clock time and channel setting are restored correctly, each timer program you have made will start at its start time unless its end time has elapsed.

Changing VCR Plus+® Setting

The VCR Plus+ programing system assigns a VCR Plus+ guide channel to the TV channels and the cable channels. These guide channel numbers are also called the VCR Plus+ channel codes. Most TV listings have a section, usually a chart, indicating the guide channel numbers assigned to each station.

To ensure that VCR Plus+ timer recording operates correctly, it is necessary to set the VCR Plus+ “Guide Channel Set” for each station.

If you have moved to a different area or if a broadcasting station’s channel number has been changed, perform the following steps to set the correct guide channel number.

AAccess Main Menu screen, then Initial Set screen

Press MENU on the Remote. Press rt to move the highlight bar (arrow) to “INITIAL SET”, then press OK or e.

BAccess Guide Channel Set screen

Press rt to move the highlight bar (arrow) to “GUIDE CHANNEL SET”, then press OK or e.

C Input guide channel number		GUIDE CHANNEL SET
Press rt or the Number keys to select
		GUIDE CH :	6
		VCR CH : – – –
the VCR Plus+ guide channel number as
shown in the TV listing, then press OK or
e.	PRESS NUMBER KEY (0–9)
	OR ( , ), THEN (OK)
	PRESS (MENU) TO END
D Input receiving channel number		GUIDE CHANNEL SET
Press rt or the Number keys to select		GUIDE CH :	6
the number of the channel on which the		VCR CH :	47
guide channel’s broadcasts are received,
then press OK or e.	PRESS NUMBER KEY (0–9)
● Repeat steps 3 and 4 for each instance.	OR ( , ), THEN (OK)
	PRESS (MENU) TO END

E Return to normal screen

Press MENU on the Remote.