JVC RS-VP2 manual Output Setup

Page 17

LED Brightness

This selection allows the user to configure the behavior of the Front Panel LED brightness. The ‘Normal’ parameter adjusts the brightness of the Front Panel LED when the menu is being navigated. The ‘Navigate’ parameter adjusts the brightness of the Front Panel LED during normal usage, when the menu is not being navigated.

User Mode

You have limited access to the output timing controls in ‘Normal’ mode. In ‘Advanced’ user mode, you have access to the complete set of output timing controls. Push the q button to see the current setting and the FPD displays either ‘Normal’ or ‘Advanced’ user level. Push the q button again to select the alternate mode. The default setting is ‘Normal’.

On Screen Display Control (OSD)

The User can define how long the OSD is displayed when there is no user interaction. The available options are:

OSD Off

5 Seconds

10 Seconds

20 Seconds

Toggle

When “OSD Off” is selected, the menu will not be displayed on screen, although navigation can be done using the front panel display. When “x Seconds” is selected, the menu will be displayed on screen, without user interaction, for the respective amount of time. When “Toggle” is selected, the menu will not “time out” and the User must use the “Exit” button to make the menu disappear. While in “Toggle” mode, the unit can also be switched into an “OSD Off”/”Toggle” mode by pressing the “Menu” button twice. This can be useful while doing display calibration.

Serial Port Rate

The serial port is used by the automation system controllers to control the RS-VP2. The serial port baud rate defaults to 19200 bps, but can be changed using the p or q button.

The supported baud rates are:

4800 bps (4.8K)

9600 bps (9.6K)

14400 bps (14.4K)

19200 bps (19.2K)

38400 bps (38.4K)

57600 bps (57.6K)

Factory Default

The Factory Default option allows you to reset all system settings to their factory defaults.

1- Press either the p or q button. The FPD displays ‘No’. 2- Press the same button to switch to ‘Yes’.

3- Confirm this selection by pressing the Enter button.

NOTE: Resetting the RS-VP2 to the factory defaults will cause all previously saved settings to be lost. Record any important settings before performing this action.

Software Update

Use this parameter to install the latest software into your RS-VP2. The latest software is available at www.jvc.com/pro. The website includes complete download install instructions.

12V Trigger Level

The state on the 12V triggers can be changed so that the connected device is in the correct state

when triggered by the RS-VP2.

Information

This setting shows information about the current Input and Output status of the system.

This screen is helpful during troubleshooting.

Input Information

Input

Note that if HDCP is present “(HDCP)” will also be displayed

Signal Type (Resolution/Colorspace)

Deinterlacing Mode

The user-selected deinterlacing mode is displayed here. Note that if PReP is turned “On”, “PReP” will also be displayed

Mosquito Noise Reduction/Fine Detail/Edge Enhancement Settings

Aspect Ratio

Audio Source

Output Information

Output (Analog or Digital/Colorspace/Gamut)

Format

Framerate

Viewing Mode

— The selected Output Picture Control Preset is displayed here

Trigger 1 and Trigger 2 Status

Aspect Ratio

Display Profile

Output Setup

Analog/Digital Output

The RS-VP2 can output either an analog or digital video signal. The default setting is for the digital, HDMI, output to be active. To output to a display with an analog input, insure that this setting is set to ‘Analog (BNC)’

Output Format

The current selected output format will be highlighted in the OSD in red. To select a different output format, highlight it first and then press the u button. Adjustment of advanced timing controls can also be made here although most displays do not need ‘custom’ timing. The User Mode, in the Configuration menu, must be changed to ‘Advanced’ for the advanced timing controls to be accessible. For a complete list of the available output presets, see the Complete Menu Tree in Section 5.

27

28

Image 17
Contents Page Power Supply Input C t i o n 3 S e t u p Initial Setup Input Adjust Control Advanced SetupConfiguration Output SetupUnpacking and Inspection IntroductionDisplay Compatibility Requirements Remote Control Battery InstallationDocument Conventions and Menu Navigation Menu NavigationInstallation Guidelines Remote Control OverviewNon-Volatile Memory Settings Discrete IR Codes and Serial Automation ProtocolBack Panel Overview Front Panel OverviewVideo Inputs Video OutputsInitial Setup Power Supply InputConfiguring the Input Sources to Get Maximum Performance Connecting the Sources to the RS-VP2Output Setup Format Make Selection Test Patterns to UseInput Adjust Deinterlacing Game Mode 1 and Game Mode Deinterlacing Mode and PRePInput Adjust PReP On Press Move Up or Move Down to highlight Set Picture FormatSource Optimization RS-VP2 Adjustments Display Optimization Using Display AdjustmentsInput Adjust Deinterlacing Forced Input Adjust Audio Input Make SelectionAdjusting for Overscan per Input Advanced SetupSetting Up and Recalling Display Profiles Input SelectActive Aspect Ratio Frame Aspect RatioPanorama RS-VP2 Image MappingPresets Input Adjust ControlMosquito Noise Reduction DeinterlacingHdmi Configuration Picture Controls ConfigurationOutput Setup Sync Type Output Aspect Ratio ControlOutput Level Framerate ConversionPicture Controls Border Level12V Triggers GamutAudio Output Selection Display ProfilesInput Aspect Ratio Complete Menu TreePicture Control RGB RS1 RS2 D e

RS-VP2 specifications

The JVC RS-VP2 is a high-performance home theater projector designed for cinephiles and those who appreciate the seamless integration of advanced technology with sublime picture quality. At the heart of the RS-VP2 is its exceptional 4K resolution, offering a stunning pixel density that enhances clarity and detail in every frame. This projector supports HDR (High Dynamic Range) content, delivering vibrant colors and an expanded contrast ratio, allowing users to experience films and videos as they were intended to be seen.

One of the standout features of the JVC RS-VP2 is its advanced DLA (Direct Drive Laser Array) technology. This system delivers superior brightness and color accuracy while maintaining a long lifespan. With 3200 lumens of brightness, the RS-VP2 is ideal for both darkened rooms and environments with some ambient light, making it versatile for different viewing scenarios.

Additionally, the RS-VP2 boasts a high Dynamic Contrast ratio, achieving deep blacks and brilliant whites through its proprietary image processing technologies. The projector uses a 4K e-shift technology, which enhances the perceived resolution by shifting pixels, thus achieving a near-4K experience even with 1080p content. This feature makes the RS-VP2 a compelling option for users who want high-quality visuals without necessarily having to rely solely on native 4K content.

In terms of connectivity, the RS-VP2 is equipped with multiple HDMI inputs that support 4K at 60Hz, making it compatible with a variety of modern devices, including gaming consoles and streaming devices. The projector also incorporates JVC's unique Motion Enhance technology, which provides smoother motion for fast-moving scenes, making it a great choice for sports and action films.

The user interface of the RS-VP2 is designed for ease of use, featuring a remote control with intuitive navigation and quick access to frequently used settings. Additionally, it supports various installation options, including lens shift and keystone correction, ensuring flexibility in setup and positioning.

In conclusion, the JVC RS-VP2 is a state-of-the-art projector that combines advanced imaging technologies with user-friendly features. Its impressive brightness, exceptional color performance, and versatile connectivity options make it a remarkable choice for home theater enthusiasts seeking an immersive viewing experience. Whether you are watching the latest blockbuster or playing video games, the RS-VP2 delivers visuals that captivate and impress.