Magnavox VRA431AT99 owner manual Setting Up the VCR Plus+ Programming System cont’d

Page 39

Setting Up the VCR Plus+ Programming System (cont’d) 39

2

Now, compare the channel numbers you have written in the VCR PLUS+ CH. and CABLE/TV CH. columns. For stations whose VCR Plus+ and Cable/TV channels do not match, you must tell the VCR the VCR Plus+ and Cable/TV channel numbers by following steps 3 - 7. Make each entry within 60 seconds of the previous entry.

3

Press the VCR button, then press the MENU button.

4

2 Examine the lists on page 38.

		4-6
3	POWER	VCR/TV	EJECT
3	VCR	TV	CBL/DBS

PLAY

REWF.FWD

STOP

Press the PLAY/o button or the STOP/p button to select VCR SET UP, then press the F.FWD/B button.

5

Press the PLAY/o button or the STOP/p button to select VCR PLUS+ REF. MAP, then press the F.FWD/B button.

MENU

7 1

4

7

VCR PLUS+/ENTER

STATUS/EXIT

2 3

5 6

8 9

ALT. CH

0

CLEAR

CH

6

VOL

6

Look at the lists you filled in on page 38. For stations whose

VCR Plus+ and Cable/TV channels do not match, press the PLAY/o button or the STOP/p button until the arrow is beside the VCR Plus+ channel you need. Then, press the Number buttons to enter the corresponding Cable/TV channel from your list. Enter all the stations on your list.

●If you are recording from line input, press 0,0 to select AUX.

●If you are using a Cable Box/DBS, the Cable/TV chan- nel will be 3 or 4 (the Cable Box/DBS output channel) for every VCR Plus+ channel. You must set the Cable Box/DBS to the channel you want to record; leave the

SPEED TIME SEARCH PAUSE/STILL

REC/OTR MEMORY SLOW

MUTE

VCR PLUS+ CROSS REF. MAP

VCR PLUS+

CABLE/TV

9898

9999

1– – – – –> 23

22

TO SELECT CH PUSH op

THEN ENTER CH NO.

TO END PUSH EXIT

7

Press the STATUS/EXIT button.

Helpful Hints

•To erase a Cable/TV channel num- ber, repeat steps 3-5 on this page. Then, press the PLAY/o button or the STOP/p button until the arrow appears beside the Cable/TV chan- nel you need to erase. Press the CLEAR button, then press the STA- TUS/EXIT button.

•When you receive the VCR, all the VCR Plus+ channel numbers and Cable/TV channel numbers are the

same.

•If you are recording from line input, connect the audio and video cables to the AUDIO IN and VIDEO IN jacks on the back of the VCR. (Please see illustration on page 42.)

Image 39

Contents VRA431AT For Customer Use Dear Philips Magnavox product ownerFeatures Safety PrecautionsIntroduction Table of Contents Before Using Your VCR Disconnect the antenna or cable from your TV Hookups Without a Cable Box / Direct Broadcast SystemPlug in the TV and the VCR CH3 CH4Hookups With a Cable Box / Direct Broadcast System ConnectionsRecording/Viewing Any Channel Select the channel you want to watch at the Cable Box/DBS Recording One Channel/Watching AnotherHookups With a Stereo TV Press the Menu button. The display shown below will appear Turning on Your VCRPress the VCR button Press the Menu button Automatic Channel SetupAdding/Deleting Channels Automatic Channel Setup cont’dPress the STATUS/EXIT button once or twice to exit Reviewing Memorized ChannelsSetting the Clock Manual Clock SettingDo each step within 60 seconds of the previous step Setting the Clock cont’d Press the VCR button, then press the Menu button Automatic Clock SettingOFF Time ZoneDaylight-Saving Time Language Selection Child Lock When Child Lock is activatedPress the Mute button Setting the Remote to Operate a TV2Find VCR Button Remote Control ButtonsVOLume o/p Buttons Press to adjust the volume of your TV Eject ButtonVCR PLUS+/ENTER Button REWind/ ButtonIf you select Status ON, then select Counter only OFF On-Screen Status DisplaysStatus Display example only If you select Status ON, then select Counter only onVCR Display Panel Front Panel Rear Panel Read and follow the steps below to play a tape PlayingVCR light does not appear, press the VCR/TV button once RecordingRecording One Channel/Watching Another OTR CH12 One-Touch RecordingDaily Timer RecordingTimer Recording cont’d Tape Speeds Press the STATUS/EXIT button. Program WAS COMChecking or Cancelling Timer Recordings Channels Setting Up the VCR Plus+ Programming SystemSetting Up the VCR Plus+ Programming System cont’d Timer Recording with the VCR Plus+ Programming System See page 48 for more hints RF coaxial cable Rerecording Tape DuplicationPress the F.FWD/B button so that on appears beside VCR SET UP, then press the F.FWD/B buttonRepeat Play Press the PLAY/o button or the STOP/p button to selectButton to reset the real-time counter to zero Real-Time Counter MemoryWhile the status display is on-screen, press the Clear Press the VCR button Press the Time Search button Time SearchViewing a Still Picture Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Super High Speed Searching LP/SLPAutomatic Operation Features Helpful Hints Helpful Hints cont’d Cable Box/DBS Output Channel 03 or GlossarySpecifications Video Cassette Recorder Limited WarrantyAutomatic IndexPage Page Supplied Accessories