Sherwood V-768 user service Problem Possible Cause Remedy

Page 42

If a fault occurs, run through the table below before taking your unit for repair.

If the fault persists, attempt to solve it by switching the unit off and on again. If this fails to resolve the situation, consult your dealer. Under no circumstances should you repair the unit yourself as this will invalidate the guarantee!

PROBLEM

POSSIBLE CAUSE

REMEDY

 

 

 

No power

• The AC input cord is disconnected.

• Connect cord securely.

 

• Poor connection at AC wall outlet or the outlet

• Check the outlet using a lamp or another

 

is inactive.

appliance.

 

 

 

No playback

• The disc is loaded upside down.

• Reload the disc with the printed side up.

 

• The disc is not playable.

• Use a playable disc.

 

• The disc is dirty.

• Clean the disc.

 

• The rating level is not set correctly.

• Set the rating level setting correctly.

 

 

(Refer to “SETTING THE CUSTOM SETUP” on

 

 

page 37.)

 

• The symbol about invalid operation is displayed.

• Adjust the setting correctly.

 

 

(Refer to “SYMBOL ABOUT INVALID OPERATION”

 

 

on page 13.)

 

 

 

Malfunction

• The disc is scratched or dirty badly.

• Press the POWER switch to switch the power

 

 

off, press the POWER switch again and then

 

 

unload the disc.

 

 

 

No picture

• The video cords are disconnected.

• Connect the cords correctly.

 

• The incorrect selection of input source on the

• Select the input source correctly.

 

TV.

 

 

• The disc is not playable.

• Use a playable disc.

 

 

 

Noisy or distorted

• The unit is connected to a VCR directly and the

• Connect the unit so that the picture signal is

picture

copyguard function is activated.

transferred directly to the TV.

 

• The disc is dirty.

• Clean the disc.

 

• It is in rapid advance or reverse playback, or in

• Sometimes a small amount of picture distortion

 

frame advance or reverse playback.

may appear. This is not malfunction.

 

 

 

Abnormal picture

• The COMPONENT OUT is not set correctly or

• Set the COMPONENT OUT setting correctly or

 

the component video output signal is not

select the component video output signal

 

selected correctly.

correctly.

 

 

(Refer to “SETTING THE VIDEO SETUP” on

 

 

page 32 or “CHANGING THE COMPONENT

 

 

VIDEO OUTPUT SIGNAL” on page 26.)

 

 

 

Slight pause of

• The layer transition occurs during playback of

• Sometimes slight pause may occur.

picture

DVD Videos recoded in dual-layer format.

This is not malfunction.

 

 

 

 

• The audio cords are disconnected.

• Connect the cords correctly.

No sound

• The speakers are disconnected to the amplifier.

• Connect the speakers correctly.

 

• The incorrect selection of input source on the

• Select the input source correctly.

 

amplifier.

 

 

• The audio setup is not adjusted correctly.

• Adjust the audio setup correctly.

 

 

(Refer to “SETTING THE AUDIO SETUP” on

 

 

page 35.)

 

 

 

Noisy or distorted

• The disc is dirty.

• Clean the disc.

sound

• Poor connections.

• Check the connections and connect all cords

 

 

securely.

 

 

 

Remote control unit

• Batteries are not loaded or exhausted.

• Replace the batteries.

does not operate.

• The remote sensor is obstructed.

• Remove the obstacle.

 

 

 

ENGLISH

43

Page 41 Page 43
Image 42
Page 41 Page 43
Contents Class Laser Product Read this Before Operating Contents Connecting to A/V Amplifier or AC Input Cord Connecting to TV with Audio Connecting S Y S T E MConnecting to TV and VCR with Scart Remote Controls Front Panel ControlsPower Switch Remote Control Operation Loading BatteriesPlayable Disc Types Markings on the DVD VideosRegion code Symbol about Invalid Care and HandlingMode Basic PlaybackPreparations Printed side up, then close itTo stop playback and return to the menu display When selectingTo start playback from the menu of DVD VIdeo To start playback from the menu of MP3 discFrame advance / reverse playback DVD Video only To stop playbackTo pause playback To skip ahead or back during playbackRapid playback during playback Slow playbackDVD Video onlyDisplaying Disc Information FollowsWhen entering the title or chapter number When entering the elapsed timeDVD Video When using a title menu When using a DVD menuPlaying a Specific Item DVD Repeating the desired part DVD Video/CD only Repeat PlaybackRepeating a disc, title, chapter, folder, track or song DVD Video MP3 discTo clear all programmed tracks Playing Tracks DesiredClearing the programmed tracks To clear one by one Checking the programmed tracksPlaying Tracks in Random Then Random on or Random is displayed onTV screen depending on the disc Changing the Audio Language DVD Changing the Subtitle L a N G U a G ETV screen for several seconds Changing the Camera Angle DVD Playing a Scene CLOSE-UP DVDEach time this button is pressed, zoom scale Changing the Video Signal Changing the Component VideoListening with Headphones English English Setting the Language Setup When selecting Others Setting the Video Setup Then the selected item screen is displayedWhen selecting the Component OUT When selecting the Scart OUTRegional OptionWhen selecting the Screen Saver When selecting the Background To return to the main setup menu screenTo return to the previous menu screen Setting the Audio Setup When selecting the Digital OUTWhen selecting the Lpcm Select CURSOR/ENTER button Setting the Custom Setup When selecting the Parental ControlWhen selecting the Change Password To return to the main setup menu screen Setting the Others When selecting the Captions When selecting the CompressionTo return to the previous menu screen Track / song number CD, MP3 disc DVD VideoTitle, Title number DVD Video Aspect ratio DVD VideoProblem Possible Cause Remedy Specifications Code Language
Top Page Image Contents