Hint for Cable Box or Satellite Box
Setup
Connection A |
|
| (Back of DVD/VCR) |
|
(Cable box or |
|
|
| |
Satellite box) |
|
| ||
IN | OUT | RF Cable | E | |
| ||||
Cable |
| |||
|
|
| ||
|
| (supplied) |
| |
Signal | (Back of TV) |
|
Select this connection when you want to view or record a scram- bled channel. With this connection, channels cannot be changed on the DVD/VCR. You can view or record ONLY the channels you have selected on the cable box or the satellite box.
•While you are recording, only the recorded channel can be viewed.
To select channels of the cable box or satellite box
1)Turn on the DVD/VCR by pressing the POWER button, and then, press the VCR/TV button.The “POWER” light on the front panel will appear. Then, press the CHANNEL buttons to select
channel 3 or 4 (the same channel as the output channel of the cable b ox or satellite box).
• If you use the channel 4, you need to change the DVD/VCR’s RF output to channel 4. Refer to “RF Output Channel”.
2)At the TV, select channel 3 or 4 (the same channel as you have selected at step 1).
3)At the cable box or satellite box, select the channel you want to
view or record.
Connection B | (Back of DVD/VCR) |
| ||
| (Cable box or |
| ||
Cable | Satellite box) | E | ||
Signal |
| IN | OUT |
|
RF Cable (supplied) |
| RF Cable | (Back of TV) | |
|
| |||
Select this connection when you want to change channels on the DVD/VCR. With this connection, you may watch one channel while recording another.
• You may not view or record a scrambled channel.
To select channels of the cable box or satellite box
1)At the cable box or satellite box, select channel 3 or 4 (the same channel as the DVD/VCR’s RF output channel.)
• Refer to “RF Output Channel”.
2)At the TV, select the same channel as the output channel (3 or 4) of the cable box or satellite box.
3)Turn on the DVD/VCR by pressing the POWER button, and then, press the VCR/TV button. The “POWER” light on the front panel will appear. Then, select the channel you want to view or record.
To play back a tape
Follow the steps 1) to 2) above. Then, play back a tape.
• Refer to “Playback” on page 11.
To view one channel while recording another
1)While you are recording on the DVD/VCR, press the VCR/TV but- ton.
2)At the cable box or satellite box, select the channel you want to view.
Connection to an Audio System
Method 1 | Method 2 |
Stereo system | Dolby Digital decoder, |
Analog audio | MD deck or DAT deck |
input jacks |
|
AUDIO 
LR
COAXIAL
Digital audio input jack
Audio cable |
|
|
(supplied) |
|
|
DVD/VCR | DVD/VCR | VCR |
AUDIO OUT |
| |
(Analog) | L |
|
AUDIO OUT |
| AUDIO IN |
R |
|
| VIDEO OUT | VIDEO IN | |
| or |
|
|
| DVD |
|
|
DIGITAL | AUDIO | ||
AUDIO OUT | OUT | OUT | VIDEO OUT |
| |||
Y
L
CB
COAXIAL
R
CR
Audio Coaxial
Digital cable
(commercially
available)
DIGITAL | AUDIO OUT |
| DVD | OUT |
|
| OUT |
| |||
| DIGITAL |
| AUDIO | ||
|
|
|
|
| VIDEO OUT |
AUDIO OUT |
|
|
|
| Y |
|
| L |
|
| |
|
|
|
|
| |
|
|
|
|
| CB |
COAXIAL
R
CR
Note
•If output is Dolby Digital encoded audio, connect to a Dolby Digital decoder, and set “DOLBY DIGITAL” to “ON” in the AUDIO menu. (Refer to pages
•The audio source on a disc in a Dolby Digital 5.1 channel surround format cannot be recorded as digital sound by an MD or DAT deck.
•Unless connected to a Dolby Digital decoder, set “DOLBY DIGITAL” to “OFF” in the AUDIO menu. Playing a DVD using incorrect settings may generate noise distortion, and may also damage the speakers. (Refer to pages
•Set “DOLBY DIGITAL” to “OFF” in the AUDIO menu for con- necting to an MD deck or DAT deck. (Refer to pages 20- 21.)
•By hooking this unit up to a
– 6 – | EN |