Kodak DRHD-120 manual Volume

Page 42

AdditionalInformation

Problem

Solution

		• The remote control is too far from the player, or the angle with the remote
	The remote control doesn't seem to	sensor is too wide.
	work.	Use the remote within its operating range.
		• The batteries are exhausted. Put in new batteries.

		Some DVD discs do not output digital audio.
		• Switch your amplifier to the player's analog outputs.
		Dirt, dust, etc. on the disc.
		• Clean the disc.
		Interconnects are not fully inserted into the terminals (or are not connected).
		• Check that all interconnects are firmly inserted.
		Dirty or oxidized plugs/terminals.
		• Clean the plugs/terminals.
	No audio, or audio is distorted.	Incorrect audio cable connection.
		• Check the audio connections.
		Player's output is connected to the amplifier's phono (turntable) inputs.
		• Connect to any set of inputs except phono.
		The disc is paused.
		• Press (play) to exit the pause mode.
		Incorrect amplifier settings.
		• Check that the volume is turned up ,that the speakers are on, the input function
		set correctly, etc.

		Incorrect Audio menu settings.
	The analog audio is OK, but there	• Make sure that the Digital Audio Out setting is set to PCM or Bitstream.
	appears to be no digital audio signal.	Check that the PCM or Bitstream settings are suitable for your amplifier
		-check the amp’s instruction manual.

	Noticeable difference in DVD and CD	• DVDs and CDs use different recording methods. This is not a malfunction.
	volume.

		• If this unit is connected to a non-DTS compatible amplifier or decoder using a
		digital audio cable, please connect to a DTS compatible amplifier or decoder.
	No DTS audio output.	If you do not do this, noise will be output if you try and play a DTS disc.
	No DTS audio output.	• If this unit is connected to a DTS-compatible amplifier or decoder using a

		digital audio cable, check the amplifier settings, and that the cable is properly
		connected.

NOTE

•Static electricity or other external influences may cause malfunctioning of this unit. In this case, unplug the power cord and then plug back in. This will usually reset the unit for proper operation. If this does not correct the problem, please consult your nearest service center.

42 Additional Information

Image 42

Contents Page Precautions PrecautionsImportantSafety Instructions Important Safety InstructionsTableofContents Keep in mind the following when using the remote control Putting the batteries in the remote controlUsing the remote control BeforeYouStartAlso this can play MPEG4 disc Compatible DiscsThis unit can play DVD-R Discs recorded as DVD video format Jpeg Photo in DiscsControls&Display Front PanelDisplay AngleRotation Rear Panel Remote Controller Unit Edit REC ModeSetup EnterTimeshift TV ModeSubtitle TitleConnection Connection for Video Output TerminalsConnection for Audio Output Terminals Connection for A/V Input TerminalsConnection for DV Gettingstarted Turning on and offScreen Saver BasicPlayback Playing a DVD discPlaying an Audio CD Button Playing a Jpeg CD Playing MPEG4 MovieLoad a Jpeg CD Picture rotation and zoomTwice to stop a DVD HDD modePlaying a program of HDD Press Play buttonSkip Forward/Backward AdvancedPlaybackFast Forward/Backward Frame by Frame Playback DVD onlySongs Press Select the desired song by using orUsing Then press Enter buttonPress Subtitle button during playing Selecting Subtitles DVD onlySelecting Audio Languages DVD only Button, then press Enter buttonRepeating a Title, Chapter Repeat DVD/Audio CD disc onlyPicture is zoomed Switching the Camera AngleZoom screen DVD/HDD only Press Angle button during playingDirect Search DVD only BookmarkRecording Basic recordingTimer Recording VPS/PDC Erasing a settingChanging a setting STANDBY/ON buttonYou want to start recording from Recorder to control the camcorder usingButton twice to stop PLAY, STOP, PausePress Play or Timeshift RecordingCopying from HDD to DVD ProgramEditing the title of DVD+R/DVD+RW Editing the chapter of DVD title Delete Editing the program of HDDChange Thumbnail DubbingOSD Language UsingtheSetupMenuBasic Operations SET TimePress Enter button after selecting Start Factory ResetChannel Setup Channel ScanTune the channel fine by pressing Or button Select the channel you want to modify by using or buttonSelect Prog Num by using or button Deleting a channelVideo Output Country SetupScreen Format Analog OutputRating SET PasswordEqualizer Press button after selecting ChangeDVD Auto Chapter Timer RecordRecord Quality Audio LanguagePress Enter button after selecting Yes Scandisk HDDFormat HDD Specifications AdditionalInformationAdditional Information Troubleshooting Problem SolutionVolume WARRANTYand Distributor