LG Electronics 3828VA0565M, MF056B, 141K TX) How to use, Refer to How to connect, Reference

Page 10

Installation

-HDMITM, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing.

-This set can receive the High-Definition Multimedia Interface (HDMI) or Input of Digital Visual Interface(DVI).

-This set supports HDCP (High-bandwidth Digital Contents Protection) Protocol for the set (480p, 720p, 1080i) modes.

-When you connect to HDMI/DVI Source devices (DVD Player, STB or PC) that support AUTO HDMI/DVI Plug & Play, this sets the HDMI/DVI source devices automatically. After reading HDMI/DVI source devices, using Display Data Channel (DDC) Protocol, Extended Display Identification Data (EDID) stored in the set is used.

If HDMI/DVI Source devices do not support AUTO HDMI/DVI, the resolution is set manually.

-When Source Devices have DVI Output Connector, you must connect audio with separated cable.

(Refer to <How to connect>)

How to connect

1. When Source Devices (DVD Player or Set Top Box) support HDMI.

-If Source Devices have HDMI Output Connector, Source Devices connect to the set with HDMI Cable .(not supplied with the product).

-If Source Devices support Auto HDMI, automatically, Source Devices divert output resolution in 1280 x 720p. But if not, refer to the reference Manual of Source Devices and select resolution manually.

-To get the best picture quality, adjust the DVD Player or Set Top Box output resolution to 1280 x 720p.

-Because HDMI sends Digital Video and Audio with one cable, there is no need for a special Audio Cable when using a HDMI Cable.

2.When Source Devices (DVD Player or Set Top Box) sup- ports DVI.

-If Source Devices have DVI Output Connector, Source Devices connect to the set with HDMI to DVI Cable (not sup- plied with the product).

-If Source Devices support Auto DVI, automatically, Source Devices divert output resolution in : 1280 x 720p. But if not, refer to the reference Manual of Source Devices and select resolution manually.

-To get the best picture quality, adjust the DVD Player or Set Top Box output resolution to 1280 x 720p.

-In this case, use another cable for audio. When Source Devices have Analog Audio Output Connector, RGB/DVI Audio Input of the set connect to Audio Cable (not supplied with the product). And then you can listen to normal Audio.

3.When PC supports DVI.

-If PC have DVI Output Connector, Source Devices connect to the set with HDMI to DVI Cable (not supplied with the product).

-To get the best picture quality, adjust the PC graphics card to 1024 x 768, 60Hz.

-Use the the set’s HDMI/DVI (VIDEO) for video connections, depending on your PC connector.

-If the graphics card on the PC does not output analog RGB and DVI simultaneously, connect only one of either RGB Input or HDMI/DVI Input to display the PC on the set.

-If he graphics card on the PC does output analog RGB and DVI simultaneously, the set to either RGB Input or HDMI/DVI Input; (the other mode is set to Plug and Play automatically by the set.)

-Then, make the corresponding audio connections. If using a sound card, adjust the PC sound as required.

-In this case, use another cable for audio. When PC (or sound card of PC) have Analog Audio Output Connector, RGB/DVI Audio Input of the set connect to Analog Audio Cable (not supplied with the product). And then you can lis- ten to normal Audio.

Reference

Cable sample (not supplied with the product)

HDMI Cable

Analog Audio Cable

 

(RCA type)

HDMI to DVI Cable

Analog Audio Cable

(Stereo to RCA type)

 

How to use

1.Connect the HDMI/DVI Source Devices(DVD Player or Set Top Box or PC) and the set.

2.Turn on the display by pressing the POWER button on the set and HDMI/DVI Source Devices remote control.

3.Select HDMI/DVI Input source in Main Input option of PIP/DW menu.

4.Check the image on your set. There may be noise associat- ed with the resolution, vertical pattern, contrast or brightness in HDMI/DVI Source Devices. If noise is present, change the HDMI/DVI Source Devices to another resolution, change the refresh rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC graphics card can not changed, change the PC graphics card or consult the manufacturer of the PC graphics card.

Notes:

-Depending on the graphics card, DOS mode may not work if you use a HDMI to DVI Cable.

-Avoid keeping a fixed image on the set screen for a long period of time. The fixed image may become permanently imprinted on the screen. Use the Orbiter screen saver when possible.

-When Source Devices are connected with HDMI/DVI Input, output PC Resolution(VGA, SVGA, XGA), Position and Size may not fit to Screen. As shown on page 29, press the MENU button to adjust the screen Position of the set and contact an PC graphics card service centre.

-When Source Devices connected HDMI/DVI Input output the set Resolution(480p, 720p, 1080i), the set Display fit EIA/CEA-861- B Specification to Screen. If not, refer to the Manual of HDMI/DVI Source Devices or contact your service centre.

-In case HDMI/DVI Source Devices Cable is not connected or poor cable connection, "No Signal" OSD display will appear. And in case of Video Resolution not being supported by the set output in HDMI/DVI Source Devices, "No Signal" OSD display will appear. Refer to the Manual of HDMI/DVI Source Devices or contact your service centre.

10 PLASMA TV

Image 10
Contents Plasma TV Do not use water while cleaning the set Safety InstructionsEarth wire should be connected Do not insert any object into the exhaust ventEnglish Contents Installing Batteries Remote Control Key FunctionsNumber buttons Location and Function of Controls Front Panel ControlsBack Panel Component InputExternal Equipment Viewing Setups 42PX4R / 42PX5R Series Resolution Horizontal Vertical Displayable Monitor SpecificationRGB / Hdmi mode 50PX4R / 50PX5R Series Resolution Horizontal VerticalRefer to How to connect How to connectHow to use ReferenceAccessories Optional ExtrasSwivel function option Installation OptionsTo Install on a Desktop To Mount on a WallTurning on the Set Turning on the set just after installationTurning on the set power cord is still connected On-Screen Menu Language Selection optionOn screen menus Manual Programme Tuning Auto Programme TuningFine Tuning Channel Menu OptionsProgramme Edit Assigning a Station NameBooster option Favourite ProgrammePicture Menu Options Sound Menu OptionsTime Menu Options Special Menu Options Screen Menu OptionsTeletext option Setting the Picture FormatInitializing Reset to original factory settings Picture Size ZoomTOP Text option Simple Text optionSpecial Teletext Functions PIP Picture-in-Picture Feature Precaution for Using the Memory Card Memory CardSlot Some MagicStor Plus cards are not usablePreview Image Display How to insert and eject the card Inserting a CardJpeg Decoding Support Image Display Ejecting a cardScreen Components Jpeg File Viewing OptionsPhoto Selection and PopUp menu Mark/Unmark for some file Mark/Unmark for Jpeg fileMark/Unmark for all files Jump MediaJpeg File Viewing Options Image Adjustment Next / previous Image Selection Image Pause Slide ShowShown/Hidden Menu File Information Jpeg File Viewing Options Jpeg file Deletion and CancelScreen Saver MP3 File Selection and Playback Current Playing Time/Total Playing TimePause Playback MP3 File Playing OperationStop/Pause Playback Stop Playback Mark/Unmark for MP3 fileDuring playing the MP3 During stopping the MP3MP3 File Playing Operation MP3 file deletion and Cancel Programming a code into a remote mode Programming the RemoteProgramming Codes VCRsHdstb No picture Troubleshooting ChecklistNo sound 42PX5R / 42PX5RH 50PX5R / 50PX5RH Product Specifications42PX4R / 42PX4RH 50PX4R / 50PX4RH 42PX4R-ZB / 42PX4RH-ZB 50PX4R-ZB / 50PX4RH-ZB