GND and HI-POT Test, HI-POT auto-check

*Auto-control interface and directions

(1)Adjust in the place where the influx of light like floodlight around is blocked. (illumination is less than 10 lux).

(2)Adhere closely the Color analyzer(CA210) to the module less than 10 cm distance, keep it with the surface of the Module and Color analyzer's prove vertically.(80° ~ 100°).

(3)Aging time

-After aging start, keep the power on (no suspension of power supply) and heat-run over 5 minutes.

-Using 'no signal' or 'POWER ONLY' or the others, check the back light on.

▪ Auto adjustment Map(using RS-232C to USB cable)
RS-232C COMMAND
[CMD		ID	DATA]
Wb		00	00	White Balance Start
Wb		00	ff	White Balance End
	RS-232C COMMAND						CENTER
		[CMD ID DATA]			MIN	(DEFAULT)				MAX
		Cool	Mid	Warm		Cool		Mid	Warm
R Gain		jg	Ja	jd	00	172		192	192	192
G Gain		jh	Jb	je	00	172		192	192	192
B Gain		ji	Jc	jf	00	192		192	172	192
R Cut						64		64	64	128
G Cut						64		64	64	128
B Cut						64		64	64	128

Color Temperature : COOL, Medium, Warm.

One of R Gain/G Gain/ B Gain should be kept on 0xC0, and adjust other two lower than C0.(When R/G/B Gain are all C0, it is the FULL Dynamic Range of Module)

* Manual W/B process using adjust Remote control.

5. GND and HI-POT Test

5.1. HI-POT auto-check preparation

- Check the POWER cable and SIGNAL cable insertion condition

5.2.HI-POT auto-check

(1)Pallet moves in the station. (POWER CORD / AV CORD is tightly inserted)

(2)Connect the AV JACK Tester.

(3)Controller (GWS103-4) on.

(4)HI-POT test (Auto)

-If Test is failed, Buzzer operates.

-If Test is passed, GOOD Lamp on and move to next proc- ess automatically.

5.3.Checkpoint

(1)Test voltage

-Touchable Metal : 3 KV / min at 100 mA

-SIGNAL : 3KV / min at 100 mA

(2)TEST time: 1 second. (case : mass production )

(3)TEST POINT

-Touchable Metal => LIVE & NEUTRAL : Touchable Metal.

-SIGNAL => LIVE & NEUTRAL : SIGNAL.

6.Model name & Serial number D/L

▪Press "Power on" key of service remote control. (Baud rate : 115200 bps)

▪Connect RS232 Signal Cable to RS-232 Jack.

▪Write Serial number

▪Must check the serial number at the Diagnostics of SET UP menu. (Refer to below).

▪After enter Service Mode by pushing "ADJ" key,

▪Enter White Balance by pushing "►" key at

Balance".

EZ ADJUST

0. Tool Option1				Whit Balance
1. Tool Option2				Whit Balance
1. Tool Option2
2. Tool Option3			Color Temp.	◄	Cool
			R-Gain
3. Tool Option4			R-Gain		172
			G-Gain
4. Tool Option5			G-Gain		172

5.	Commercial Tool Option		B-Gain		192

6.	Country Group		R-Cut		64

7. ADC Calibration			G-Cut		64
			B-Cut
8.	White Balance	►	B-Cut		64

9.	10 Point WB		Test-Pattern		ON
10. Test Pattern			Backlight		100
11. EDID D/L			Reset		To Set

12.Sub B/C

13.Ext. Input Adjust

"8. White

►

6.1. Signal Table

CMD

LENGTH

ADH

ADL

DATA_1

. . .

Data_n

DELAY

CMD : A0h

LENGTH : 85~94h (1~16 bytes)

ADH : EEPROM Sub Address high (00~1F)

ADL : EEPROM Sub Address low (00~FF)

Data : Write data

CS : CMD + LENGTH + ADH + ADL + Data_1 +...+ Data_n

Delay : 20ms

*After you finished all adjustments, Press "In-start" key and compare Tool option and Area option value with its BOM, if it is correctly same then unplug the AC cable. If it is not same, then correct it same with BOM and unplug AC cable. For correct it to the model's module from factory Jig model.

*Push the "IN STOP" key after completing the function inspection. And Mechanical Power Switch must be set “ON”.

4.5.Outgoing condition Configuration

■When pressing IN-STOP key by SVC remocon, Red LED are blinked alternatively. And then automatically turn off. (Must not AC power OFF during blinking)

6.2. Command Set

Adjust mode	CMD(hex)	LENGTH(hex)	Description

EEPROM WRITE	A0h	84h+n	n-bytes Write (n = 1~16)

*Description

FOS Default write : <7mode data> write

Vtotal, V_Frequency, Sync_Polarity, Htotal, Hstart, Vstart, 0, Phase

Data write : Model Name and Serial Number write in EEPROM,.

Copyright ©	LG Electronics. Inc. All rights reserved.	- 13 -	LGE Internal Use Only
Only for training and service purposes