LG Electronics 37LC2R Adjustment of RF/AV/S-VIDEO, Adjustment of Component, Adjustment of RGB

d. Model Name/Monitor Name:

Model Name
37LC2R-TH	00	00	00	FC	00	33	37	4C	43	32	52	2D	54	48	0A	20	20	20
42LC2R-TH	00	00	00	FC	00	34	32	4C	43	32	52	2D	54	48	0A	20	20	20

e. Checksum: Changeable by total EDID data

5.ADC Calibration

5.1Adjustment of RF/AV/S-VIDEO

*Required Equipments

•Remote controller for adjustment

•802F Pattern Generator, Master (MSPG-925FA), etc.

•MSPG-925FA Pattern Generator

(Which has Video Signal: 100% Color Bar Pattern shown in Fig. 1)

=> Model : 202 / Pattern: 33 (PAL : ZH, TH) Model : 201 / Pattern : 33 (NTSC : MH)

(Fig. 1)

5.1.1 Method of Auto RF/AV/S-VIDEO Color Balance.

1)Press the FRONT-AV KEY on R/C for converting input mode.

2)Input the Video Signal: 100% Color Bar signal into AV3(ZH), AV1(TH), VIDEO1(MH)

3)Set the PSM to Standard mode in the Picture menu.

4)Press INSTART key on R/C for adjustment.

5) Press the (Vol.+) key to operate the set, then it becomes automatically

6) Auto-RGB OK means the adjustment is completed

5.1.2 Requirement

•This AV color balance adjustment should be performed before White Balance Adjustment.

•After color balance adjustment, You must push "power on" key. ("Power on" key is "Access Heat_run mode")

5.2Adjustment of Component.

*Required Equipments

•Remote controller for adjustment

•802F Pattern Generator, Master (MSPG-925FA), etc.

•MSPG-925FA Pattern Generator

(Which has 720p YPbPr signal : 100% Color Bar Pattern shown in Fig. 2 )

=> Model: 217 / Pattern: 33

•It is very import to use correct adjustment pattern like Fig. 2.

-Within the pattern, color sequence should be aligned : W-Y-C-G-M-R-BLUE-BLACK

(If color sequence is reversed (Black -> ... -> White), reverse the pattern with REV key, when using

Master pattern generator like MSPG-925)

-If Minimum Black Level and/or Maximum White Level is not correct, Do select 100% Color Bar Pattern.

(Fig. 2)

5.2.1 Method of Auto Component Color Balance

1)Input the Component 720p 100% Color Bar(MSPG-925FA model:217, pattern:33) signal into Component.

(ZH : component , TH/MH : component 1 or 2)

2)Set the PSM to Standard mode in the Picture menu.

3)Press the INSTART key on R/C for adjustment.

4)Press the (Vol. +) key to operate the set , then it becomes automatically.

5)Auto-RGB OK means the adjustment is completed.

5.3Adjustment of RGB

*Required Equipments

•Remote controller for adjustment

•802F Pattern Generator, Master (MSPG-925FA), etc.

•MSPG-925FA Pattern Generator

(Which has XGA [1024x768] 60Hz PC Format output signal : 100% Color Bar Pattern shown in Fig. 3 )

•It is very import to use correct adjustment pattern like

Fig. 10.

- Within the pattern, color sequence should be aligned

: W-Y-C-G-M-R-BLUE-BLACK

(If color sequence is reversed (Black ->...-> White), reverse the pattern with REV key, when using Master pattern generator like MSPG-925)

-If Minimum Black Level and/or Maximum White Level is not correct, Do select 100% Color Bar Pattern.

(Fig. 3)

5.3.1 Method of Auto RGB Color Balance

1)Input the PC 1024x768@60Hz 1/2 Black&White Pattern (MSPG-925FA model:3, pattern:33) into RGB.

2)Set the PSM to Standard mode in Picture menu.

3)Press the INSTART key on R/C for adjustment.

4) Press the (Vol. +) key operate To set , then it becomes automatically.

5) Auto-RGB OK means adjustment is completed.

- 12 -