LG Electronics 60LA7400 Preventing Image burn or Burn-in on your TV, Screen, YyGenerated Sound

		IMPORTANT SAFETY INSTRUCTIONS	5
yyDot Defect	For USA and Canada
The Plasma or LCD panel is a high technology
product with resolution of two million to six million
pixels. In a very few cases, you could see fine dots
		FCC NOTICE
on the screen while you’re viewing the TV. Those

	dots are deactivated pixels and do not affect the	This equipment has been tested and found to
	performance and reliability of the TV.
		comply with the limits for a Class B digital device,
yyGenerated Sound
		pursuant to Part 15 of the FCC Rules. These limits
	“Cracking” noise: A cracking noise that occurs
		are designed to provide reasonable protection
	when watching or turning off the TV is generated by
		against harmful interference in a residential
	plastic thermal contraction due to temperature and
		installation. This equipment generates, uses and can
	humidity. This noise is common for products where
		radiate radio frequency energy and, if not installed
	thermal deformation is required.
		and used in accordance with the instructions, may
	Electrical circuit humming/panel buzzing: A low level
		cause harmful interference to radio communications.
	noise is generated from a high-speed switching
		However, there is no guarantee that interference
	circuit, which supplies a large amount of current
		will not occur in a particular installation. If this
	to operate a product. It varies depending on the
		equipment does cause harmful interference to radio
	product.
		or television reception, which can be determined
	This generated sound does not affect the
		by turning the equipment off and on, the user is
	performance and reliability of the product.
		encouraged to try to correct the interference by one
yyTake care not to touch the ventilation openings.
		or more of the following measures:
	When watching the TV for a long period, the
			- Reorient or relocate the receiving antenna.
	ventilation openings may become hot. This does
			- Increase the separation between the
	not affect the performance of the product or cause
			equipment and the receiver.
	defects in the product.
			- Connect the equipment to an outlet on a circuit
yyIf the TV feels cold to the touch, there may be a
			different from that to which the receiver is
	small “flicker” when it is turned on. This is normal,
			connected.
	there is nothing wrong with TV. Some minute dot
			- Consult the dealer or an experienced radio/TV
	defects may be visible on the screen, appearing as
			technician for help.
	tiny red, green, or blue spots. However, they have
		This device complies with part 15 of the FCC Rules.
	no adverse effect on the TV’s performance. Avoid
		Operation is subject to the following two conditions:
	touching the LCD screen or holding your finger(s)
		(1) this device may not cause harmful interference
	against it for long periods of time. Doing so may
		and (2) this device must accept any interference
	produce some temporary distortion effects on the
		received, including interference that may cause
	screen.
		undesired operation of the device.
		Any changes or modifications in construction of
	Preventing “Image burn” or “Burn-in” on your TV	this device which are not expressly approved by
		the party responsible for compliance could void the
screen
		user’s authority to operate the equipment.
			NOTE TO CABLE/TV INSTALLER

ENGLISH

yyIf a fixed image displays on the TV screen for a long period of time, it will be imprinted and become a permanent disfigurement on the screen. This is “image burn” or “burn-in” and not covered by the warranty.

yyIf the aspect ratio of the TV is set to 4:3 for a long period of time, image burn may occur on the letterboxed area of the screen.

yyAvoid displaying a fixed image on the TV screen for a long period of time (2 or more hours for LCD, 1 or more hours for the Plasma TV) to prevent image burn.

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.