Peerless Industries D-LPL-100, RTLPL-100S, SP730P Installation to Solid Concrete and Cinder Block

Page 5

Installation to Solid Concrete and Cinder Block

WARNING

When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90 specifications. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid breaking out the back of the hole when entering a void or cavity.

Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.

1

Level and use wall plate as template to mark center

of holes. Drill two 1/4" (6 mm) dia. holes to a

minimum depth of 2" (51 mm). Insert anchors (E) in holes flush with wall as shown in fig 1.3. Place wall arm (A) over anchor and secure with wood screw (D) as shown in figures 1.4 and 1.6. Make sure wall arm is level, and tighten all fasteners. See figure 1.5.

WARNING

Tighten screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power.

Never tighten in excess of 80 in. • lb (9 N.M.).

WARNING

Concrete anchors are not intended for attachment to concrete wall covered with a layer of plaster, drywall, or other finishing material as shown below. If mounting to concrete wall covered with plaster/drywall is unavoidable, plaster/drywall (up to 5/8" thick) must be counterbored as shown below. Be sure concrete anchors do not pull away from concrete when tighten- ing screws. If plaster/drywall is thicker than

5/8", custom fasteners must be supplied by installer.

Drill holes

fig 1.3

concrete

and insert

anchors.

 

wall

 

 

E

Place wall

fig 1.4

WALL PLATE

plate over

anchor and

 

D

secure with

 

screw.

 

E

 

 

Tighten all

fig 1.5

 

fasteners.

 

 

 

 

CORRECT

INCORRECT

E

VIEW

 

 

D

A

 

A

 

 

 

 

 

 

CUTAWAY

plaster/

concrete

plaster/

concrete

A

 

dry wall

 

dry wall

 

 

 

 

 

fig 1.6

5 of 24

ISSUED: 06-10-05 SHEET #: 095-9225-8 09-25-06

Image 5
Contents Features Installation and Assembly LCD Screen Long Pivot Wall MountTable of Contents Tools Needed for AssemblyAccessories FH C Skip to on Installation to Wood Stud WallInstallation to Solid Concrete and Cinder Block Or G Or G Optional Caractéristiques Installation et assemblageOutils nécessaires pour l’assemblage AccessoiresTable des matières RemarquesSP730P SP730P-S Description QTÉ. Nº de Pièce LPL-100MUR À Montants EN Bois Installation sur un mur à montants en boisCoupeen Ou G Détail Optionnel Características Accesorios Herramientas necesarias para el montajeContenido NotasSP730P SP730P-S Descripción Cant. N de pieza De pieza Lista de piezasInstalación en una pared con montantes de madera Nivele y utilice la placa de apoyo como plantilla EN EL Caso DE LA Configuración DE Montaje DE Vesa Detalle Optativo