Technicolor - Thomson 30L03B Using the remote control for other equipment, Automatic code search

Page 10

Using the remote control for other equipment

The remote control supplied with your set can be used for other equipment, such as video recorders, PC or DVD players. This page provides information concerning the remote control’s use with these types of equipment.

 

 

 

 

VCR

DVD

VCR

 

Press the VCR button

 

DVD

 

 

Press the DVD button

 

 

 

 

On/Standby

On/Standby

 

 

 

 

MENU

 

To display the main menu

To display the main menu

 

 

 

 

Vertical scrolling in menus

Vertical scrolling in menus

 

 

 

 

Horizontal scrolling in menus

Horizontal scrolling in menus

OK

 

To confirm an action

To confirm an action

EXIT

 

To close a menu

To close a menu

0-9

 

 

To directly access channels or enter

To enter numeric values or select options

 

 

 

 

numeric values

in menus

PR+/PR-

 

To change channels

 

AV

 

To select AV input

To select

REV

 

Rewind

Rewind

PLAY

 

Play

Play

FWD

 

Fast forward

Fast forward

STOP

 

Stop

Stop

PAUSE

 

Pause picture

Pause picture

REC

 

Record

 

Programming the remote control

Automatic code search

This method can be used to automatically find the most appropriate code protocol for your appliance.

1.Switch on the appliance you wish to use the remote control with.

2.Press the relevant button for this appliance on the remote control, and while holding this button down, press

the standby button until the remote control light comes on. Release the two buttons.

3.Point the remote control at the appliance and press PLAY. Wait until the light stops flashing. If the appliance has not gone into standby mode after five seconds, press the PLAY button again to continue the search for the next set of codes.Repeat this operation until the appliance goes into standby mode. There are 20 sets of codes.

4.When the appliance goes into standby mode, press the standbybutton on the right up side to switch it on again. Then press the REV button to put it back in standby mode, and if necessary, keep pressing until the appliance goes into standby.

5.Press the STOP button and hold it down until the remote control light goes off.

Note: you can cancel the programming operation at any time by pressing the EXIT button.

Manual programming

This method involves carrying out a manual search for the code to be used for controlling your other appliances.

1.Switch on the appliance you wish to use the remote control with.

2.Press the relevant button for this appliance on the remote control, and while holding this button down, enter one of the codes relevant to your make of appliance (there is a list of codes at the end of this manual). If the remote control light flashes you have entered the wrong code or it is not possible to program the remote control.

3.Point the remote control at the appliance and press the relevant button (VCR or DVD). Press thestandby button. If the appliance does not go into standby mode, try another code.

Depending on the year of manufacture and the type of appliance, some functions may not be available.

Certain codes may cover more functions than others. Test the functions you can control and, if appropriate, try other codes.

Note here the code(s) which work best.

VCR DVD

When you change the remote control’s batteries, remember to reprogram it.

10

Image 10
Contents Important Safety Instructions Page Page AC Power Supply Cord II Safety TipsBefore Setting Up Important InformationIV Caution If problems occur during useWhen using the LCD TV Be sure to disconnect all cables before moving the LCD TVIntroduction Supplied AccessoriesDifferent territories Batteries for the Remote Control Precaution on battery useII Preparation Switching on Getting StartedText purple button Teletext Remote control TV functionsColoured buttons 9To select a channel by its numberAutomatic code search Using the remote control for other equipmentManual programming Channels SET-UP Automatic InstallationInitial set-up Arranging channels in order OrganiserOrganiser Deleting channelsManual Installation Automatic updateManual channel set-up Operation General operationLast programme ZoomPanning function for Zoom Press the Return button to return to last watched programmeReturn go back to Overview menu Adjusting the soundSound Broadcast OptionsPhase, Synchronization, V-Position,H-Position Adjusting the picturePicture Preferences Setting the PreferencesSleep timer TV LockChanging the character set temporarily Accessing TeletextNavigation bar NewsflashSubtitles Direct access to subpagesFastext Scart 1 AV1 / AV1 RGB input-output PIC Picture in Computer ModeOther Information Audio R/L and video Cvbs Cinch sockets AV3 inputYCrCb component and Audio R/L input Connecting headphonesVideo socket AV3-S and Audio R/L input YPrPb for Video, D-Sub for PC and Audio inputConnecting a video recorder Connecting a ComputerTrouble Shooting TV setColors fade AntennaPossible interference