Extron electronic LPVM-1 installation instructions Mounting the Display Device, 68-1946-01

Page 2

Low Profile VESA Mount Kit User Guide (Continued)

Mounting the LPVM-1 to a Mud Ring or UL-Certified Junction Box in Drywall:

NOTE: See the caution on previous page about weight restrictions.

a.Follow the instructions provided by the manufacturer to cut the hole and install the mud ring or junction box.

b.Attach plate 1 to the mud ring or junction box, using the four #632 screws provided. Ensure the tongue is facing upwards.

c.Connect conduit to the junction box and run the cables to the installation site.

UL-certified 2-gang Wall Box

#6-32 screws (4)

Mounting the Display Device

5.If necessary, remove all cables from the display device.

NOTE: To VESA mount the TLP 700TV, it is necessary to remove

the base and the plastic enclosure from the back. For

full instructions, see the TLP 700MV and TLP 700TV User Guide, which is available from www.extron.com.

Do not use the VM 700T for mounting with the LPVM1.

Use the four 12 mm M4 screws (provided) to attach plate 2 to the back of the display device, using either the B-type (20 x 50 mm) or Dtype (75 x 75 mm) VESA mounting pattern. The plate should be attached securely but do not over-tighten the screws.

6.Attach the cables to the back of the display device. Feed any excess cable back into the wall, conduit, or raceway. Follow all information in the user manual provided with the display device to ensure the cables and power are connected correctly.

Extron

LPVM-1

Plate 1

 

12 mm M4

Monitor w/ B-type

Screws (4)

 

VESA Mount

Plate 2

 

7.Check the display device is working correctly (see the user manual for the display device).

8.Hook plate 2 to plate 1 by holding the display at a slight angle so that the groove of plate 2 is over the tongue in plate 1. Lower the display device so that the tongue enters the groove as far as possible.

9.Allow the bottom of the display to move inwards so that the display is parallel to the wall and the bottom tabs of plate 1 are seated over the bottom edge of plate 2.

10.Lock the two plates together by tightening the two locking screws with a screwdriver (do not over-tighten).

8

Plate 1

Plate 2

9

10

Extron USA - West

Extron USA - East

Extron Europe

Extron Asia

Extron Japan

Extron China

Extron Middle East

 

Headquarters

 

 

 

 

 

 

 

+800.633.9876

+800.633.9876

+800.3987.6673

+800.7339.8766

+81.3.3511.7655

+400.833.1568

+971.4.2991800

68-1946-01

Inside USA/Canada Only

Inside USA/Canada Only

Inside Europe Only

Inside Asia Only

+81.3.3511.7656 FAX

Inside China Only

+971.4.2991880 FAX

+1.714.491.1500

+1.919.863.1794

+31.33.453.4040

+65.6383.4400

 

+86.21.3760.1568

 

Rev A

+1.714.491.1517 FAX

+1.919.863.1797 FAX

+31.33.453.4050 FAX

+65.6383.4664 FAX

 

+86.21.3760.1566 FAX

 

06 10

© 2010 Extron Electronics. All Rights Reserved. www.extron.com

Image 2
Contents Optional Tools and Equipment Installation InstructionsOverview Disassembling the LPVM-1Mounting the Display Device 68-1946-01