4.For the
SPEED | DUPLEX |
| |
(Mbps) | AUTO | ||
10 | MODE | ||
100 |
| HALF | NEG |
|
| FULL | OFF |
|
|
| ON |
1 | 2 | 3 |
|
2 | 4 | ||
| 1 | 2 | 2 |
| PORT | ||
|
| ||
|
|
| - |
|
|
| 240VAC~ |
|
|
| 1382 |
Figure 5 - Securing AC Power Cord with the Retaining Clip
5.Install the mounting bracket on the DINRAIL. As shown in Figure 6, “Mounting the Bracket on the DINRAIL”, the bracket may be oriented either with the bracket screw above or below the DINRAIL.. Slide the hook towards the DINRAIL until it is snug and then tighten the bracket screw.
1519 |
Figure 6 - Mounting the Bracket on the DINRAIL
Copyright © 2009 Allied Telesis, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesis, Inc.
DINRAIL Mounting Bracket
Installation Guide
Overview
This guide provides assembly instructions for assembling and mounting a DINRAIL mounting bracket with one of the following Allied Telesis products:
•
•
•
Media Converters
•
Verifying the Package Contents
Make sure that these components are included in your package:
•10 DINRAIL mounting brackets
•20 M3 mounting screws
•10
•This installation guide
If any item is missing or damaged, contact your Allied Telesis sales representative for assistance.
Assembling a DINRAIL Bracket and Meda Converter
1.Find your media converter model in Figure 1, 2 or 3 on pages 2 and 3 as listed here:
Figure 1
•
•
•
•
•
•
•
•
•
•
•
Figure 2
•
Figure 3
•
•
4.For the
SPEED | DUPLEX |
| ||
(Mbps) | AUTO | |||
10 | MODE | |||
100 |
| HALF | NEG | |
|
| FULL | OFF | |
|
|
| ON | |
1 | 2 | 3 |
| |
2 | 4 | |||
1 | 2 | |||
| 2 | |||
| PORT | |||
|
| |||
|
|
| - | |
|
|
| 240VAC~ | |
|
|
| 1382 |
Figure 5 - Securing AC Power Cord with the Retaining Clip
5.Install the mounting bracket on the DINRAIL. As shown in Figure 6, “Mounting the Bracket on the DINRAIL”, the bracket may be oriented either with the bracket screw above or below the DINRAIL.. Slide the hook towards the DINRAIL until it is snug and then tighten the bracket screw.
1519 |
Figure 6 - Mounting the Bracket on the DINRAIL
Copyright © 2009 Allied Telesis, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesis, Inc.
DINRAIL Mounting Bracket
Installation Guide
Overview
This guide provides assembly instructions for assembling and mounting a DINRAIL mounting bracket with one of the following Allied Telesis products:
•
•
•
Media Converters
•
Verifying the Package Contents
Make sure that these components are included in your package:
•10 DINRAIL mounting brackets
•20 M3 mounting screws
•10
•This installation guide
If any item is missing or damaged, contact your Allied Telesis sales representative for assistance.
Assembling a DINRAIL Bracket and Meda Converter
1.Find your media converter model in Figure 1, 2 or 3 on pages 2 and 3 as listed here:
Figure 1
•
•
•
•
•
•
•
•
•
•
•
Figure 2
•
Figure 3
•
•
PN | Page 4 | PN | Page 1 | PN | Page 4 | PN | Page 1 |