Panasonic PV C2063 operating instructions Important Safeguards and Precautions

Page 2
ANTENNA LEAD IN WIRE
NEC - NATIONAL ELECTRICAL CODE

Important Safeguards and Precautions

READ AND RETAIN ALL SAFETY AND OP- ERATING INSTRUCTIONS. HEED ALL WARN- INGS IN THE MANUAL AND ON UNIT

INSTALLATION

1 POWER SOURCE CAUTION

Operate only from power source indicated on unit or in this manual. If uncertain, have your Electric Utility Ser- vice Company or Video Products Dealer verify your home power source.

2 POWER CORD PLUG

For safety, this unit has a polarized type plug (one wide blade), or a three-wire grounding type plug. Al- ways hold the plug firmly and make sure your hands are dry when plugging in or unplugging the AC power cord. Regularly remove dust, dirt, etc. on the plug.

POLARIZED PLUG CAUTION:

The plug fits into outlet one way. If it cannot be fully inserted, try reversing it. If it still will not fit, have an elec- trician install the proper wall outlet. Do not tamper with the plug.

GROUNDING PLUG CAUTION:

The plug requires a three-hole grounding outlet.

If necessary, have an electrician install the proper outlet. Do not tamper with the plug.

3 POWER CORD

To avoid unit malfunction, and to protect against electrical shock, fire or personal injury:

-Keep power cord away from heating appliances and walking traffic. Do not rest heavy objects on, or roll such objects over the power cord.

-Do not tamper with the cord in any way.

-An extension cord should have the same type plug (polarized or grounding) and must be securely connected.

-Overloaded wall outlets or extension cords is a fire hazard.

-Frayed cords, damaged plugs, and damaged or cracked wire insulation are hazardous and should be replaced by a qualified electrician.

4 DO NOT BLOCK VENTILATION HOLES Ventilation openings in the cabinet release heat generated during operation. If blocked, heat build-up may result in a fire hazard or heat damage to cassettes.

For your protection:

a.Never cover ventilation slots while unit is ON, or operate unit while placed on a bed, sofa, rug, or other soft surface.

b.Avoid built-in installation, such as a book case or rack, unless properly ventilated.

5 AVOID EXTREMELY HOT LOCATIONS OR SUDDEN TEMPERATURE CHANGES

Do not place unit over or near a heater or radiator, in direct sunlight, etc. If unit is suddenly moved from a cold place to a warm place, moisture may condense in unit and on the tape causing damage.

6 TO AVOID PERSONAL INJURY

Never place unit on support or

stand that is not firm, level, and adequately strong. The unit could fall causing serious injury to a child or adult and damage to the unit.

Move any appliance and

cart combination with care. Quick stops, excessive force, and uneven

surfaces may cause objects to overturn.

• Carefully follow all operating instructions.

OUTDOOR ANTENNA INSTALLATION

1SAFE ANTENNA AND CABLE CONNECTION

An outside antenna or cable system must be properly grounded to provide some protection against built up static charges and voltage. Section 810 of the National Electrical Code, ANSI/NFPA 70 (in Canada, part 1 of the Canadian Electrical

Code) provides information regarding proper grounding

of the mast and supporting

GROUND

ANTENNA

DISCHARGE UNIT

CLAMP

(NEC SECTION 810-20)

structure, grounding of the

 

GROUNDING

lead-in wire to an antenna

 

CONDUCTORS

ELECTRIC

(NEC SECTION 810-21)

discharge unit, size of grounding

SERVICE

GROUND CLAMPS

EQUIPMENT

 

POWER SERVICE

conductors, location of antenna

 

 

GROUNDING

 

ELECTRODE SYSTEM

(NEC ART 250, PART H)

discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

2KEEP ANTENNA CLEAR OF HIGH VOLTAGE POWER LINES OR CIRCUITS

Locate an outside antenna system well away from power lines and electric light or power circuits so it will never touch these power sources should it ever fall. When installing antenna, absolutely never touch power lines, circuits or other power sources as this could be fatal.

USING THE UNIT

Before unit is brought out of storage or moved to a new location, refer again to the INSTALLATION section of these safeguards.

1 KEEP UNIT WELL AWAY FROM WATER OR MOISTURE, such as vases, sinks, tubs, etc.

2 IF EXPOSED TO RAIN, MOISTURE, OR STRONG IMPACT, unplug unit and have it inspected by a qualified service technician before use.

3 ELECTRICAL STORMS

During a lightning storm, or before leaving unit unused for extended periods of time, disconnect all equipment from the power source as well as the antenna and cable system.

4 WHEN UNIT IS PLUGGED IN

• DO NOT OPERATE IF:

-liquid has spilled into unit.

-unit was dropped or otherwise damaged.

-unit emits smoke, malodors, or noises.

Immediately unplug unit, and have it inspected by a service technician to avoid potential fire and shock hazards.

Never drop or push any object through openings in unit. Touching internal parts may cause electric shock or fire hazard.

Keep magnetic objects, such as speakers, away from unit to avoid electrical interference.

5 USING ACCESSORIES

Use only accessories recommended by the manufacturer to avoid risk of fire, shock, or other hazards.

6 CLEANING UNIT

Unplug unit. Use a clean, dry, chemically untreated cloth to gently remove dust or debris. DO NOT USE cleaning fluids, aerosols, or forced air that could over-spray, or seep into unit and cause electrical shock. Any substance, such as wax, adhesive tape, etc. may mar the cabinet surface. Exposure to greasy, humid, or dusty areas may adversely affect internal parts.

SERVICE

1 DO NOT SERVICE PRODUCT YOURSELF

If, after carefully following detailed operating instructions, the unit does not operate properly, do not attempt to open or remove covers, or make any adjustments not described in the manual. Unplug unit and contact a qualified service technician.

2 REPLACEMENT OF PARTS

Make sure the service technician uses only parts specified by the manufacturer, or have equal safety characteristics as original parts. The use of unauthorized substitutes may result in fire, electric shock, or other hazards.

3 SAFETY CHECK AFTER SERVICING

After unit is serviced or repaired, request that a through safety check be done as described in the manufacture’s service literature to ensure video unit is in safe operating condition.

2

Image 2
Contents Combination VCR Operating Instructions Model No. PV-C2063 Important Safeguards and Precautions Loading the Batteries AccessoriesRemote Control Serial NoUnit Information Table of Contents Location of Controls Number KeysFront View of the Unit and Indicators Initial Setup Rear View of the UnitFor DSS/Cable Box ConnectingInitial Setup Ready to Play Manual Clock Set Reset all unit Memory FunctionsPower SELECT/SET CH UP Action CH Down VOL UP VOL Down Reset Language, Channels, Clock 2003 THU 1200PMTime Zone Adjust You can operate on the unit Playback a Tape Record On a TapeReady Check List To prevent tape jamPlayback Source Recording Editing unit Selecting Input ModeCopy Your Tapes Dubbing TV Operation Night ModeNight Press Night to set Night mode Press Night toMTS Broadcast/TV Stereo System Operation Select Audio Mode for TV ViewingPress Display to display the broadcast signal Receivable Broadcast TypesTimer TV Timer FeaturesON-TIMER with Alarm TIMER/FM On TimerAlarm. Time changes Order shown Sleep TimerInstant Alarm LeftClosed Caption System Closed Caption Mode FeatureClosed Caption Mode Selections Recording and Playing Back a Closed Caption/Text ProgramTV Operation Caption On Mute FeaturePress repeatedly to Select desired mode Press to selectHow to use the FM radio FM Radio SetupFM Antenna Setup To select Audio Mode for FM RadioPicture Adjustment OperationProgramming Timer RecordingRepeat to set Press To selectTo Clear program Cancel a Timer Recording Recording is in progressTo Replace program Index Search To cancel, press PlayTape Operation ExampleAuto Shut Off Auto Operation FunctionsTape Position Display Auto PlaybackCommercial Skip Zero SearchRepeat Play PressVCR Lock Special VCR FeaturesWeak Signal Display ON/OFF Press Action twice toPress to select Remote Warning Display SET UP TV screenPress Select TV Press to set on or OFFEnter Secret Code Chip Control FeatureProcess of V-Chip Control Feature Enter Code Setup Blocking Changing your secret codeProcess of V-Chip Control Feature Enter Code Setup Blocking Setup US Movies RatingsSetup US TV Programs Ratings Press to select and to set ratings to be blockedTo View a Blocked Program / Movie When V-Chip Control is activatedBlocking Message Temporarily Deactivate V-Chip ControlSet to Combo Universal Remote Control SetupUsing the Universal Remote Control Set to DSS CableDSS Brand Code Numbers Cable Box Brand Code NumbersBlue Screen Display On-Screen Display OSDVCR Status & Clock Display Channel & Function DisplayBefore Requesting Service VCR CorrectionParts Labor Service Contact Number Limited WarrantyLimited Warranty Coverage Carry-In, Mail-in or In-Home ServiceCustomer Services Directory Limited Warranty Limits And ExclusionsRealizando Configuracion Inicial Connexiones/Configuracion InicialConectando Ajuste Manual del RelojGrabación con temporizador One Panasonic Way Secaucus New Jersey IndexLSQT0666A San Gabriel Industrial Park, Carolina, Puerto Rico

PV C2063 specifications

The Panasonic PV C2063 is a cutting-edge model in the realm of multifunctional printers, designed to meet the diverse needs of businesses and home offices alike. This printer stands out due to its impressive combination of performance, innovative technology, and user-friendly features.

One of the main highlights of the Panasonic PV C2063 is its exceptional printing speed. Capable of delivering up to 60 pages per minute, it ensures that high-volume print jobs are completed swiftly, making it an ideal choice for busy environments. The device also offers a high-quality output with a resolution of up to 1200 x 1200 dpi, guaranteeing sharp text and vibrant images in every print.

In terms of paper handling, the PV C2063 is equipped with a robust input capacity. It features multiple paper trays, allowing for versatile media handling, which includes various paper types and sizes. The automatic duplex printing capability further enhances its efficiency, reducing paper waste while saving time and costs.

The printer incorporates advanced scanning technologies, making it not only a powerful printed but also an effective scanner. It includes features such as color scanning and an automatic document feeder (ADF), capable of handling multiple documents at once. This functionality becomes a great asset for digitizing documents quickly, enhancing workflow, and ensuring efficient archival processes.

Connectivity is another area where the PV C2063 excels. It supports a variety of connection options, including USB, Ethernet, and wireless connections, which facilitate easy integration into any office network. This connectivity allows for seamless printing from various devices, including smartphones and tablets, providing flexibility and convenience for users.

To further enhance its usability, the PV C2063 features an intuitive touchscreen interface. This user-friendly control panel makes it easy to navigate through different functions, settings, and even troubleshoot minor issues.

Durability and reliability are paramount in any office equipment, and the Panasonic PV C2063 does not disappoint. Built with high-quality materials and engineering, it is designed to handle the rigors of daily use while maintaining optimal performance.

In summary, the Panasonic PV C2063 printer is a versatile and powerful tool for any office. With its high-speed printing, superior output quality, advanced scanning features, and multiple connectivity options, it stands as a top choice for those seeking efficiency and reliability in their printing solutions. Whether for crafting reports, presentations, or any other documentation, this printer promises to enhance productivity in any setting.