Sylvania SRC2319 owner manual Channel SET UP Again, Deleting or Adding, Automatic Clock Setting

AUTOMATIC CLOCK SETTING

Make sure ...

• The TV/VCR is turned on.

• Confirm the TV/VCR is receiving a RF (Radio

Frequency) signal from either an antenna or cable

NOTE: During Auto Clock CH Search, the picture may be distorted. This is normal.

4 Enter the channel number that contains the Automatic Clock Setting Signal

system connection using the ANT IN jack on the

rear of the TV/VCR.

NOTE:

• If a cable converter box is being used, make sure it

is powered on.

• You must use the TV/VCR remote control to per-

form the clock setting procedure.

• If the TV/VCR is connected directly to a cable

converter box or satellite box, the local PBS station

must be selected on the cable box itself, and the

TV/VCR must be set to the output channel of the

cable converter box or satellite box (usually chan-

nel 3 or 4), to be able to set up or correct the clock

automatically

Press the MENU button on the remote control.

Press the PLAY/K or STOP/L button to select “SETTING CLOCK”.

Press the F.FWD/B button to select setting clock.

Press the STOP/L button to select “AUTO CLOCK CH”.

Press the F.FWD/B or REW/s buttons until you locate Auto Clock Set station number. See item 3 above.

– M E N U –

TIMER PROGRAMMING PICTURE CONTROL

BSETTING CLOCK CHANNEL SET UP USER’S SET UP V-CHIP SET UP LANGUAGE [ENGLISH] CAPTION [OFF] ZERO RETURN

TIME SEARCH

– SETTING CLOCK –

AUTO CLOCK	[ON]
AUTO CLOCK CH SEARCH
B AUTO CLOCK CH	[ 45]
MANUAL CLOCK SET
D.S.T.	[OFF]

Press the MENU button to exit the screen.

1Select “SETTING CLOCK”

Press the MENU button on the remote control.

Press the PLAY/K or STOP/L but- ton to select “SETTING CLOCK”. Press the F.FWD/B button to enter “SETTING CLOCK” menu.

– M E N U –

TIMER PROGRAMMING PICTURE CONTROL

BSETTING CLOCK CHANNEL SET UP USER’S SET UP V-CHIP SET UP LANGUAGE [ENGLISH] CAPTION [OFF] ZERO RETURN

TIME SEARCH

5Turn off the TV/VCR

Once the TV/VCR is turned off , it will periodically check and set the correct date and time.

CHANNEL SET UP AGAIN

Make sure ...

2 Set “AUTO CLOCK” to [ON]	– SETTING CLOCK –
Press the F.FWD/B button until	B AUTO CLOCK [ON]
	AUTO CLOCK CH SEARCH

•Press the POWER button to turn on the TV/VCR.

AUTO CLOCK [ON] appears.	AUTO CLOCK CH	[ 02 ]
	MANUAL CLOCK SET
	D.S.T.	[OFF]

3Begin “AUTO CLOCK CH SEARCH”

Press the STOP/L button to select “AUTO CLOCK CH SEARCH”.

1Select “CHANNEL SET UP”

Press the MENU button on the remote control.

Press the PLAY/K or STOP/L but- ton to point to “CHANNEL SET UP”.

Then, press the F.FWD/B button.

– M E N U –

TIMER PROGRAMMING PICTURE CONTROL SETTING CLOCK

BCHANNEL SET UP USER’S SET UP V-CHIP SET UP LANGUAGE [ENGLISH] CAPTION [OFF] ZERO RETURN

TIME SEARCH

Press the F.FWD/B button.

• The TV/VCR is now searching

for the station which contain the

auto clock set signal. The search

for a signal may take up to 20

seconds per channel.

•“_ _” appears at the lower left of

the screen when the search has

ended.

– SETTING CLOCK –

AUTO CLOCK [ON]

BAUTO CLOCK CH SEARCH

AUTO CLOCK CH	[ 02 ]
MANUAL CLOCK SET
D.S.T.	[OFF]

– AUTO CLOCK CH SEARCH –

08 10 13

2Begin auto preset

Press the PLAY/K or STOP/L but- ton to point to “AUTO PRESET”. Then, press the F.FWD/B button. The tuner scans and memorizes all the active channels in your area.

– CHANNEL SET UP –

ADD / DELETE CH (TV)

BAUTO PRESET

• Auto Clock station- write down

the number(s) that appear on the

screen. These are the auto clock

station(s) in your area. See item

4 below.

_ _

3After scanning

The tuner stops on the lowest memorized channel.

DELETING (OR ADDING)

•If no number(s) appear on the TV screen, there are no stations in your area which contain the Auto Clock signal. Auto Clock Setting is not possible. Please use Manual Clock Setting on page 11.

Press the MENU button to exit the screen.

CHANNEL

The channels you no longer receive or seldom watch can be deleted from the memory. (Of course, you can add the deleted channel into the memory again.)

- 12 - EN

1K09