Mega System Tech iCV-02, iCV-01a, iCV-01b, iCV-03 manual Introduction, Features

Page 4

Chapter 1: Introduction

Chapter 1: Introduction

Section 1. Features

iCAMView is a compact stand-alone web-server capable of remote video surveillance. It can be accessed from anywhere in the world via a standard browser by entering the IP, account and password. Each system can simultaneously support any two combinations of USB PC cameras be it regular, infrared or pan-tilt. With its built-in web-server, iCAMView can stream video images directly to the Internet without have to go through a computer. iCAMView features a Windows-based software that allows the user to archive streaming video directly into the hard-drive. The same software also allows the user to monitor multiple cameras on one screen.

Features:

•Built-in Web Server

•10/100Mbps Fast Ethernet Network Access

•Support Any Java-Enabled Web Browser

•LCD display shows the IP address, Subnet Mask and Gateway

•32-Bit RISC CPU

•1MB Flash Memory

•8MB Dynamic Memory

•Support Up to 30 Remote Viewers for each camera

•Allow Up to 8 User Accounts and Passwords

•5.3VDC 1A Maximum

•Operating Temperature: 0°C ~ 60°C

•Operating Humidity: 10% ~ 90%

•Dimensions: 48mm x 63mm x 21m

•Weight: 75g

•For Indoor Use. Protective housing required for use

•Network Protocol: HTTP, TCP/IP, UDP, SMTP, PPPoE, Dynamic DNS, DNS Client, SNTP, BOOTP, DHCP, FTP, SNMP

•Support All USB PC Camera with VIMICRO ZC0301 Plus processor built-in

•Resolution: 640 x 480, 320 x 240, 160 x 120.

•Frame Rate: Up to 20fps in 320 x 240

•Motion JPEG streaming video

•2 USB Ports for PC Cameras

•USB 1.1 & 2.0 compliant

•Can combine with two different PC cameras

•Support Pan/Tilt and Infrared USB PC Camera

Section 2. iCAMView as a Remote Surveillance System

Once iCAMView is installed, the user can check any of the connected PC cameras using a standard web browser. The user can monitor and control these cameras simply by entering the IP address of the iCAMView into a Web Browser from anywhere in the world. For instance, the user can be in Australia but is able to

iCAMView user manual

-1-

Image 4

Contents Copyright Information Technical Support and Contact InformationContents IMultiView 50 . Installing iMultiView 50 . Using iMultiView Features IntroductionPackage Contents Light indicators on iCAMView LAN Port LED Installation Procedure ICAMView installation flowchartInstallation Procedure ICAMView, USB Camera and the NetworkICAMView, USB Camera and the Network Using iCAMView Utility to Setup IP & Update Firmware Installing iCAMView UtilityUsing iCAMView Utility Setup Wizard Using iCAMView Utility to Setup IP & Update Firmware Using iCAMView Utility to Setup IP & Update Firmware Using iCAMView Utility to Setup IP & Update Firmware Launch iCAMView IP Configuration IPAddressIP Configuration Set an IP Address for iCAMView AdvancedDevice Password IP Configuration iCAMView Advanced settingsUpgrade Firmware Ii. Management ProtocolUpgrade Firmware Updates iCAMView firmware About RefreshICAMView Web Manager Web-Camera SelectionICAMView Main Menu Web-Camera Selection System Status InformationSystem Information Current Connections Ii. System InformationBasic Settings Camera SettingsCamera Settings Network Account Settings Setting up Camera a Similar with Camera BIndividual Camera Configuration NetworkIi. DNS Server IP IP AddressIii. Port Number Iv. Ethernet Dynamic DNSVi. PPPoE Account SettingsUser Account User Name Can only access the Camera and Information Advanced Settings Event NotificationEvent Notification Send Email ICAMView Event Selection List ICAMView Event Start Up Camera a or Camera B Enable Motion DetectionICAMView Motion Detection ICAMView Motion Detect Email Notification Image Recording Camera a or Camera B Begin End hhmmMail / FTP ICAMView Email of Image RecordedFTP Settings FTP Server Ii. Email Settings E-mail ServerIii. Sending Test Mail ICAMView test mail functionSystem Settings Iv. Email Address BookSystem Time System TimeIv. Snmp Settings Iii. LED SettingsIi. System Restart Image Server Interface Language LanguageIi. Email Preference About ICAMView AboutViewing images using PDA / Web enabled mobile phone ICAMView checking for latest firmware to upgradeICAMView image Installing iMultiView IMultiViewDevice IMultiView Display the current Camera settings Display the Motion Detection Settings Image RecordingAvifilethree digit numerical sequence Server Require Authentication Configure Settings for Email NotificationNotified Email Address Snmp Settings Using Snmp to update network portsIMultiView IMultiView View SystemUser Help Drag-and-Drop FeatureStep Double click on the icon on the desktop, to view the images Appendix a Router Configuration Port Forwarding for iCAMViewSMC SMC2404WBR Appendix a Router Configuration TCP UDP Protocol Type Enabled/Disabled For ID#2 Service Port 9001 Service IP Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Appendix a Router Configuration Action Allow always Appendix a Router Configuration Click Save to save the settings Private Port Type Appendix a Router Configuration Enable Checked Appendix a Router Configuration Method 1 Using iCAMView Utility Appendix B Methods to Update iCAMView FirmwareMethod 2 Through iCAMView Web Appendix C IP Address, Subnet and Gateway Subnetting and Subnet Masks Subnet Mask Routing and FilteringAppendix D Glossary Term Definition