Universal Remote Control UR2-CBL-CV04 operating instructions Introduction, Replacing Batteries

Operating Instructions

For CABLEVISION

Remote Control

UR2-CBL-CV04

Universal Remote Control, Inc.

www.universalremote.com

OCE-0030A Rev 23(01/20/12)

1Introduction

The remote control is designed to operate the Scientific-Atlanta Explorer 8000, Pioneer Voyager DVR and the Pace Micro DVR Series set top boxes and the majority of TV's on the market.

2Replacing Batteries

Before you program or operate the remote control, you must install two AA alkaline batteries.

STEP1 Remove the battery compartment cover on the back of your remote control.

STEP2 Check battery polarity carefully, and install the batteries as shown in the illus- tration below.

STEP3 Replace the battery compartment cover.

4Operations

Default State :

Device Default: Scientific-Atlanta Explorer 8000

Volume Default : TV volume and mute through the TV, with the option of controlling volume and mute through the Cable. Refer to Section D for programming the volume and mute through your Cable.

3 Button Functions

5Programming the Remote Control.

A.Three-Digit Code Programming Method.

The remote control can be programmed by pressing in a three digit code number that corre- sponds to particular manufacturers and brands of TV.

The three-digit code numbers are listed in the code table of the instruction manual.

STEP1 Turn on the TV you wish to program.

STEP2 Press the [TV] button and the [SEL] button simultaneously for 3 seconds. The iO button will turn on indicating the unit is ready to be programmed.

*Tip : The iO button will light on for 20 seconds. The next step must be entered while the iO button is on.

www.universalremote.com

STEP3 PointtheremotecontroltowardtheTVand enterthethree-digitcode numberassigned toyourbrandfromthecodetables.

*Tip : The TV will turn off when the correct three- digit code number has been entered. You can verify you have selected the correct code by pressing the [MUTE] button, the TV should turn on or turn off.

*Note:Ifthereismorethanonethree-digitnumber listedforyourbrand,tryonecodenumberata timeuntilyourTVturnsoff.

STEP4 Storethethree-digitcodenumberbypress- ingthe[TV]buttononceagain.TheiObutton willblinktwicetoconfirmthatthecodehas beenstored.

*Note:Tryallthefunctionsontheremotecontrol. If anyofthefunctionsdonotworkasthey should,repeatfromStep2usingthenextthree- digitcodenumberfromthesamebrandlist.

B. Auto Search Method.

If the three-digit code numbers assigned to your brand do not turn off your TV or the code tables do not list your brand, you can use the Auto

Search Method to find the correct three-digit code number for your TV by the following steps:

STEP1 TurnontheTVyouwishtooperate.

STEP2 Pressthe[TV]buttonandthe[SEL]button

simultaneouslyfor3seconds.

TheiObuttonwillturnon.

*Tip:TheiObuttonwilllightonfor20seconds. The next step must be entered while the iO buttonison.

STEP3 Pressthe[CH ]or[CH ]buttononestep atatimeorkeepitpressed.Theremotewill emitaseriesofPowerON/OFFcommands. Releasethe[CH ]or[CH ]buttonassoon astheTVturnsoff.

*Tip:Youcanverifythatyouselectedthecorrect codebypressingthe[MUTE]button.TheTV shouldeitherturnonorturnoff.

STEP4 Pressthe[TV]buttontostorethecode.The iObuttonwillblinktwicetoconfirmthatthe codehasbeenstored.

C. To Find the Three Digit Code Number That was Stored in the TV.

STEP1 Pressthe[TV]buttonandthe[SEL]button simultaneouslyfor3seconds.