Toshiba 17HLV85 appendix Connecting an Hdmi or a DVI device to the Hdmi input, Playback Appendix

Page 17

Connecting an HDMI™ or a DVI device to the HDMI input

Introduction

The HDMI[1] input on your TV/DVD receives digital audio and uncompressed digital video from an HDMI device or uncompressed digital video from a DVI[2] device.

This input is designed to accept HDCP[3] program material in digital form from EIA/CEA-861/861B–compliant[4]consumer electronic devices (such as a set-top box or DVD player with HDMI or DVI output).

The HDMI input is designed for best performance with high definition video signals. It will accept and display 480i, 480p, 720p and 1080i signals.

Note: The HDMI jack is not intended for connection to and should not be used with a personal computer. For PC connection, see page 20.

To connect an HDMI device, you will need:

•one HDMI cable (type A connector)

For proper operation, it is recommended that you use as short an HDMI cable as possible. You should not encounter difficulty if you use an HDMI cable that is shorter than 16.4 ft (5m).

HDMI cable transfers both video and audio. Separate analog audio cables are not required (see illustration below).

You must set the HDMI audio input setting to “HDMI” in the AUDIO menu (see page 40).

Some CDVs (Video CDs) may not output digital audio signals. In that case, you may hear sound by connecting analog audio cables. If you do use analog audio cables for this reason, you will need to set the HDMI audio input setting to “DVI” to hear the analog audio (see page 40). Note: If you connect an HDMI device and analog audio cables and play media with digital audio output, to hear digital audio you must set the HDMI audio input setting to “HDMI” (page 40).

HDMI device￿￿￿￿￿ ￿￿￿￿￿￿￿￿

￿￿￿￿

￿￿￿

 

[1]HDMI = High-Definition Multimedia Interface.

[2]DVI = Digital Video Interface.

[3]HDCP = High-bandwidth Digital Content Protection.

[4]EIA/CEA-861/861B compliance covers the transmission of uncompressed digital video with high- bandwidth digital content protection, which is being standardized for reception of high-definition video signals.

Because this is an evolving technology, it is possible that some devices may not operate properly with the TV/DVD.

To ensure that the HDMI or DVI device is reset prop- erly, it is recommended that you follow these proce- dures:

•When turning on your electronic components, turn on the TV/DVD first, and then the HDMI or DVI device.

•When turning off your electronic components, turn off the HDMI or DVI device first,and then the TV/DVD.

To connect a DVI device, you will need:

•one HDMI–to–DVI adapter cable (HDMI type A connector)

For proper operation, the length of an HDMI-to-DVI adapter cable should not exceed 9.8 ft (3m). The recommended length is 6.6 ft (2m).

•one pair of standard analog audio cables

An HDMI-to-DVI adapter cable transfers only video. Separate analog audio cables are required (see illustration below).

You must set the HDMI audio input setting to “DVI”

DVI device ￿￿￿￿￿ ￿￿￿￿￿￿￿￿

￿￿￿

in the AUDIO menu (see page 40).

￿￿￿

Rear lower

TV/DVD back panel of TV/DVD

your TV/DVDConnecting

your TV/DVDSetting up

TV/DVD’s FeaturesUsing the

DVD

TV/DVD back panel

HDMI, the HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing, LLC.

17

Playback

Appendix

5U90121A(E)P11-21

17

6/17/05, 10:59 AM

Page 16 Page 18
Image 17
Page 16 Page 18
Contents DVD Playback Appendix Your TV/DVDConnectingIntroduction Safety PrecautionsFCC compliance information Introduction Your TV/DVDConnectingTV/DVDup Federal Communications Commission FCCS3126A AccessoriesLCD HeatDisc Never use the unit when moisture condensation may occur PrecautionsImportant notes about your LCD TV Moisture condensation may occur in the following situationsOn cleaning discs Structure of disc contentsOn handling discs On storing discsPlayable discs On Video CDsSetting up your TV/DVD Connecting your TV/DVDUsing the TV/DVD’s features IntroductionExploring your new TV/DVD Stereo VCR Connecting a VCRSelecting a location for the TV/DVD Option 2 For Subscribers to Scrambled Cable TV Service Connecting a cable converter box or AntennaOption 1 For Subscribers to Basic Cable TV Service Satellite Receiver Connecting a satellite receiver and a VCRStereo VCR From Antenna Stereo VCR Connecting your TV/DVD Connecting a camcorderPlayback Appendix Connecting an Hdmi or a DVI device to the Hdmi inputTo connect an Hdmi device, you will need To connect a DVI device, you will needDigital Theater Systems DTS Connecting an amplifier equipped with a DTS decoderDolby Digital Connecting an amplifier equipped with a digital audio input Connecting an amplifier equipped with an Mpeg audio decoderMPEG2 sound Channel digital stereoPower connection Connecting a PC Personal ComputerTo use AC power Monitor Display modesTo install the batteries Installing the remote control batteriesLearning about the remote control Setting up your TV/DVDChanging the on-screen display language Starting setupTo select a language PressAdding channels to the TV/DVD’s memory Game modeProgramming channels automatically Adding and erasing channels manuallyProgramming your favorite channels Adjusting the channel settingsSwitching between two channels Selecting a password Using the Locks menuUsing the TV/DVD’s Features To select your password and access the Locks menuUsing the V-Chip parental control feature Locking the video inputs Locking channelsDVDPlayback Setting the GameTimerTMUsing the panel lock feature Labeling channels UsingtheTo create channel labels To erase channel labelsTV/DVDConnecting Setting the clockSelecting the video input source Labeling the video input sourcesSet the desired minutes and channel As in step Setting the on timerTo cancel the on timer Selecting the picture size DVD PlaybackNatural picture size TheaterWide picture size for 43 format programsUsing the Aspect feature Selecting the cinema modeTo set the Cinema Mode to Film To set the Cinema Mode to VideoUsing the closed caption feature Setting the sleep timerSelecting the picture mode Adjusting the pictureAdjusting the picture quality Mode Picture QualityResetting your picture adjustments Using the CableClear featureSelecting the color temperature Adjusting the sound quality Adjusting the soundMuting the sound Selecting stereo/SAP broadcastsUsing the WOW surround sound feature Resetting your audio adjustmentsUsing the StableSound feature Auto power off Adjusting the back lighting featureUnderstanding the Power Return feature Displaying on-screen informationResetting your picture/audio adjustments in the PC mode Picture/Audio adjustments in the PC modeDescription about Each Setting Option Picture menu BASS/TREBLE/BALANCE To adjust the sound quality of PC modeBasic playback DVD VCD CD Resume featurePlaying a disc About Playing frame by frame DVD VCD Playing in fast reverse or fast forward directionsPlaying in slow-motion Locating a chapter or trackLocating desired scene DVD VCD CD Zooming DVD VCDMarking desired scenes DVD VCD To cancel the MarkerMarking the scenes Returning to the scenesRepeat playback DVD VCD CD Introduction Your TV/DVDConnecting Your TV/DVDSetting upRandom playback VCD CD Program playback VCD CDTo change the program To clear the program one by oneDVD menu Changing anglesTitle selection Case of Video CD playback Changing soundtrack language DVD VCDSubtitles Disc status DVD VCD CD Karaoke playbackTo turn off the PBC VCD Video CDStandard, sampling frequency, and the bit rate MP3/WMA/JPEG CD operationLimitations on display About file menu MP3/WMA CD playback CDSlide show playback CD Jpeg CD playback CDRotating an image Customizing the function settings DVD function setupPicture Setting detailsLanguage Other SoundParental Temporary disabling of parental level by DVD disc Appendix Language code listSymptom Solution TroubleshootingSymptom of DVD Solution DVD/CD Player Specifications17HLV85 20HLV85 Television Limited United States Warranty Limited Canada Warranty Memo National Service Division
Top Page Image Contents