Pioneer XV-DV430 operating instructions Pull off the protective shields of both AM antenna wires

Setting Up your XV-DV430 DVD/CD Receiver

When connecting this system or changing connections, be sure to switch the power off with the STANDBY/ON button, and disconnect the power cord from the AC outlet. Do not use these speakers with any other system or amplifier as this may result in damage or fire.

1Check that you have all the accessories, then put the batteries in the remote control.

2Connect the AM and FM antennas to the rear panel of the DVD/CD receiver.

Using the remote control

The remote control can be used within a range of about 21 ft from the remote sensor on the front panel, and within a 30 degree angle.

Precautions:

Batteries and

remote control Power cord

	STANDBY/ON
CD	FM/AM	L1/L2
DVD	TUNER TV	LINE
DISPLAY		OPEN CLOSE
	8	0
1 3		¡
4	7	4
DVD MENU		RETURN
	TUNE+
ST–		ST+
	ENTER
MUTE	TUNE–	SOUND
Video cord	VOLUME
	MASTER
	TV CONTROL
CH	INPUT	VOL

OPEN

FM antenna
AM loop antenna
Satellite speakers: •	Center (1)
•	Front/Surround (x4)
•	Subwoofer (1)
•	Speaker cords (x6)

• Non-slip pads (x24)

1Pull off the protective shields of both AM antenna wires.

2Push open the tabs, then insert one wire fully into each terminal.

3Release the tabs to secure the AM antenna wires.

4Fix the AM loop antenna to the attached stand.

To fix the stand to the antenna, bend in the direction indicated by the arrow (fig. A) then clip the loop onto the stand (fig. B).

Note: If you plan to mount the AM antenna to a wall or other surface, secure the stand with screws (fig. C) before clipping the loop to the stand. Make sure the reception is clear.

fig. A

4

6

1

FM	AM
ANTENNA UNBAL 75Ω	LOOP ANTENNA

fig. B fig. C

2

3

•The remote control may not work if there is an obstacle between the remote control and the display unit, or if the remote control is not directed towards the remote sensor of the display unit at the correct angle.

•The remote control may not work properly if strong light such as direct sunlight or fluorescent light is shining onto the unit’s remote sensor.

•The remote control may not work properly when this unit is used near devices emitting infrared rays, or when remote controls of other devices which use infrared rays are used. Also, the use of this remote control may cause other devices to work improperly.

•When the operating range of the remote becomes too short, replace the batteries.

Remote control battery caution

Incorrect use of batteries may cause leakage or rupture.

Always be sure to follow these guidelines:

• Always insert batteries into the battery compartment correctly matching the

positive ª and negative · polarities, as shown by the display inside the compartment.

•Never mix new and used batteries.

•Batteries of the same size may have different voltages, depending on brand. Do not mix different brands of batteries.

•When disposing of used batteries, please comply with governmental regulations or environmental public instruction's rules that apply in your country or area.

•In order to prevent battery leakage, remove the batteries when not using the remote control for an extended period (one month or more). If leakage occurs, carefully wipe away any battery fluid inside the compartment, and replace the batteries with new ones.

•Do not allow books or other objects to rest on top of the remote control, since the buttons may be depressed, causing faster exhaustion of the batteries.

Additional notes on connecting antennas

• Keep antenna cables away from other cables and the display unit and main set.

• To assure optimum reception, pull the FM antenna so that it is fully extended and not coiled or hanging at the rear of the unit.

• If reception with the supplied antenna is poor, see the Additional Connections section in the main operating instructions

for details on connecting outdoor antennas.

1 2 3

5 Place the AM antenna on a flat	6 Connect the FM wire antenna to the FM UNBAL 75Ω antenna terminal.
surface and point in the direction	For best results, extend the FM antenna fully and fix to a wall or door
giving the best reception.	frame. Don’t drape loosely or leave coiled up.
Don’t let it come into contact with metal	Note: The signal earth (H) is designed to reduce noise that occurs when an
objects and avoid placing near computers,
	antenna is connected. It is not an electrical safety earth.
television sets or other electrical appliances.

Additional notes on speaker placement

Place speakers as shown in step 4 to achieve the optimum surround sound effect

• Install the main front left and right speakers at an equal distance from the TV.

• For optimum effect, install the rear speakers slightly above ear level.

• This system's speakers are magnetically shielded, so there's virtually no picture color distortion when they are placed near

a TV. In the rare event that there is some picture color interference, switch power to the TV off, and wait 15 to 30 minutes

before switching on again.

• Install the center speaker above or below the TV so that the sound of the center channel is localized at the TV screen.

• When installing the center speaker on top of the TV, be sure to secure it with tape or some other suitable means.

Otherwise, the speaker may fall from the TV due to external shocks such as earthquakes, endangering those nearby or

3Connect each speaker using the color-coded speaker cords. Match them to the colored labels

above the speaker terminals.

Surround right	Surround left
(Grey)	(Blue)

		IN	IN	OUT
FRONT	CENTER	SURROUND		L
SPEAKERS	6	6		Listening position
6
L		L		R
R		TV AUDIO		LINE 1
		R		Subwoofer (Purple)
6	SUB	6
	6
	WOOFER

Front right	Center (Green)	Front left
(Red)		(White)

Connect each speaker as shown below.

Color-coded wire

(Connect to speaker)

Color-coded connector (Connect to rear panel)

1	Twist and pull off the protective
	shields on each wire.
2	Connect the wires to the
	speaker. Match the colored
	wire with the color-coded
	label (above the tabs), then
	insert the colored wire into
	the red (+) tab and the other
	wire with the black (–) tab.
3	Connect the other end to the

color-coded speaker jacks on the rear of the DVD/CD receiver (as shown at left). Make sure to insert completely.

damaging the speaker.

• Do not connect the supplied speakers with any other amplifier. This may result in malfunction or fire.

4Connect the DVD/CD receiver to your TV, then connect the supplied power cord.

1Connect one end to a video input on your TV.

Use the supplied video cord.

2Connect the other end to the video output of the DVD/CD receiver.

This player is equipped with copy protection technology. Do not connect this player to your TV via a VCR using AV cables, as the picture from this player will not appear properly on your TV.

3Connect the power cord to the AC inlet.

VIDEO IN

		IN	IN	OUT
6	6	6		L
				LINE 2
L		L		R
		TV		LINE 1
R		R

6 6 6

Y P P

VIDEO

OUT

VIDEO

For the best surround sound, setup your speakers as above. The front left and right speakers should be about 6–9 ft apart.

Remove the supplied non-slip pads from the paper, and stick four onto the base of each satellite speaker.

Actual speakers supplied may differ from those shown.

These speaker terminals can be hazardous when live. When you connect or disconnect the speaker cables, to prevent the risk of electric shock, do not touch uninsulated parts before disconnecting the power cord.

AC IN

To AC outlet

Congratulations! You're done setting up.

Printed in <XRE3074-A>