Toshiba 32HL83 Switching the main and POP pictures, Freezing the POP picture, Press Exit

Page 39

Switching the main and POP pictures

Press SWAP while you are using the POP feature to switch the main and POP pictures.

	LE	SUB	TIT
	TIT		TIT
			LE
P			A
U			U
T	FAV		DI
SE	FAV		O
			O

E

F

S

Introduction

Freezing the POP picture

ENTER

FAV

x •

1.Press FREEZE while the POP is not on the screen. The POP window will appear with a still picture.

2.Press FREEZE again to renew the still picture.

To erase the still POP window:	Still picture
Press EXIT.

Adjusting the size of the double-window

When the input signals of the main and POP pictures are 480i, you can adjust the size of each window. Continuously pressing x or • changes the size in 9 steps.

CH

VOL

EXIT EXIT

DVD CLEAR

DVD RTN
CH RTN	INPUT	RECALL	MUTE
SLOW/DIR		SKIP/SEARCH
REW	PAUSE/STEP	PLAY	FF
	AM/FM	STOP	REC
TV/	DISC
VCR	DISC

FREEZE

POP CH	SPLIT	POP DIRECT CH	FREEZE
	SWAP	CH SCAN	SOURCE

SWAP

Note:

If the signal format other than 480i is received, this feature is not available. “Not available” will appear on the screen.

39

Connecting	yourTV

Usingthe	RemoteControl


Settingup	yourTV


UsingtheTVÕs	Features


Appendix

Index

Image 39

Contents 32HL83 Dear Customer Safety PrecautionsInstallation Important Safety InstructionsCare ServiceIntroduction Supplied accessories Welcome to ToshibaTheaterLink cable Exploring your new TV Remote controlConnecting your TV Connecting a cable converter box Connecting a VCRFrom Cable Connecting a cable converter box and VCRUsing Remote Connecting a DVD player or satellite receiver and a VCRFrom Antenna Stereo VCR Receiver, set the VCR to Line in and the TV to Video Connecting a camcorder Connecting two VCRsDVI/HDCP device For example, set-top box or DVD player Connecting a device to the DVI/HDCPConnecting a device to the TheaterLink Amplifier Connecting an audio systemInstalling the remote control batteries Preparing the remote control for useRemote Control functional key chart CBL/SAT Audio VCR TV/VCR TV/SAT Searching and sampling the code of a device Device code setupOperational feature reset Using the volume lock featureDevice code table VCR setup codesCD Player setup codes Learning about the remote control Learning about the menu system Setting up your TVCable box output channel selection Using the Quick Connect GuideSelect channels using Cable box Picture mode selectionChanging the on-screen display language Selecting the antenna inputPress x or to highlight your desired language Adding channels to the TVÕs memory Programming channels automaticallyPress z to select CH Program Changing channels using SpeedSurf Changing channelsAdding and erasing channels manually Programming your favorite channels Adjusting the channel settingsSwitching between two channels using Channel Return Switching between two channels using SurfLockªUsing the TVÕs Features Labeling channels Press z to highlight Press PIC Size on the remote controlViewing the wide-screen picture formats Selecting the picture sizeAppendix Index ¥ To raise the picture, press y Press x or to display the Scroll Adjustment modeSelecting the cinema mode Using the auto aspect featureButtons 0-9 Using the POP double-window featurePress Exit Switching the main and POP picturesAdjusting the size of the double-window Freezing the POP pictureDouble-Window with keeping aspect ratio Using the programmed channel search functionAbout the auto favorite feature Using the favorite channel search functionIf you cannot remember your PIN code Using the Locks menuPress y or z to display the PIN code entering mode Entering the PIN codeTV Rating Independent rating system for broadcasters Using the V-CHIP menuPress x or to return to the Locks menu Mpaa Rating Independent rating system for moviesLocking channels Unlocking programs temporarilyRepeat steps 3 and 4 for other channels Locks menu OFF Locking video inputsChanging the PIN code Using the game timerUsing the front panel lock feature To cancel the timer Select OFF in aboveAdjusting the picture Selecting the picture modeAdjusting the picture quality Using CableClearª DNR Digital Noise Reduction Selecting the color temperatureSaving your new preferences Selecting the video input source Resetting your picture quality adjustmentsSelecting the background of the menu display Labeling the video input sources¥ To view text, highlight T1, T2, T3, or T4 Using the closed caption featureSetting the sleep timer Setting the ON-timerAdjusting the sound Muting the soundSelecting stereo/SAP broadcasts Enjoying the WOWª surround sound feature Enjoying the Dolby Virtual sound featureResetting your audio adjustments Adjusting the sound qualityTo turn on the built-in speakers Highlight on in above Using the sub-bass system SBSTurning off the built-in speakers To turn off the SBS Highlight OFF in aboveSelecting the Audio OUT sound Using the StableSound¨ featureAdjusting the back lighting feature Press x or to adjust the screen brightnessSelecting the gray level of the side panels Displaying on-screen information Viewing the demonstration modeUnderstanding the auto power off feature Understanding the last mode memory featureAppendix SpecificationsT2, T3, or T4. Turn closed captioning OFF TroubleshootingAntenna Black box appears on the screenLimited United States Warranty Limited Canada Warranty Index Toshiba VISUAL-EQUIPMENT Corporation