Pioneer VRB1332-A operating instructions Operating Environment, POWER-CORD Caution

Page 3
S002_En
D3-4-2-1-7c_En
D3-4-2-1-4_En

WARNING:

BEFORE PLUGGING IN THE UNIT FOR THE FIRST TIME, READ THE FOLLOWING SECTION CAREFULLY. The voltage of the available power supply differs according to country or region. Be sure that the power supply voltage of the area where this unit will be used meets the required voltage (e.g., 230V or 120V) written on the rear panel.

WARNING: No naked flame sources, such as lighted candle, should be placed on the apparatus. If naked flame sources accidentally fall down, fire spread over the apparatus then may cause fire.

D3-4-2-1-7a_En

This product is for general household purposes. Any failure due to use for other than household purposes (such as long-term use for business purposes in a res- taurant or use in a car or ship) and which requires repair will be charged for even during the warranty period.

K041_En

This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

Operating Environment

Operating environment temperature and humidity: +5 ºC – +35 ºC (+41 ºF – +95 ºF); less than 85 %RH (cooling vents not blocked)

Do not install in the following locations

•Location exposed to direct sunlight or strong artificial light

•Location exposed to high humidity, or poorly

ventilated location

When disposing of used batteries, please comply with governmental regulations or environmental public instruction’s rules that apply in your country or area.

H048_En

This product includes FontAvenue® fonts licenced by NEC corporation. FontAvenue is a registered trademark of NEC Corporation.

POWER-CORD CAUTION

Handle the power cord by the plug. Do not pull out the plug by tugging the cord and never touch the power cord when your hands are wet as this could cause a short circuit or electric shock. Do not place the unit, a piece of furniture, etc., on the power cord, or pinch the cord. Never make a knot in the cord or tie it with other cords. The power cords should be routed such that they are not likely to be stepped on. A damaged power cord can cause a fire or give you an electrical shock. Check the power cord once in a while. When you find it damaged, ask your nearest PIONEER authorized service center or your dealer for a replacement.

Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified service personnel.

IMPORTANT

The cut-off plug should be disposed of and must

Do not connect either wire to the earth terminal of a

not be inserted into any 13 amp socket as this can

three pin plug.

result in electric shock. The plug or adaptor or the

NOTE

FOR USE IN THE UNITED

distribution panel should be provided with 5 A fuse.

As the colours of the wires in the mains lead of this

After replacing or changing a fuse, the fuse cover in

KINGDOM

appliance may not correspond with coloured

the plug must be replaced with a fuse cover which

The wires in this mains lead are coloured in

markings identifying the terminals in your plug,

corresponds to the colour of the insert in the base

accordance with the following code:

proceed as follows ;

of the plug or the word that is embossed on the

Blue

: Neutral

The wire which is coloured blue must be connected

base of the plug, and the appliance must not be

Brown

: Live

to the terminal which is marked with the letter N or

used without a fuse cover. If lost replacement fuse

If the plug provided is unsuitable for your socket

coloured black.

covers can be obtained from your dealer.

outlets, the plug must be cut off and a suitable plug

The wire which is coloured brown must be

Only 5 A fuses approved by B.S.I or A.S.T.A to

fitted.

 

connected to the terminal which is marked with the

B.S.1362 should be used.

 

 

letter L or coloured red.

D3-4-2-1-2-2_En

Page 2 Page 4
Image 3
Page 2 Page 4
Contents DV-575A LASERPRODUCTCLASS1 Operating Environment POWER-CORD CautionContents Features Before you startBefore you start Chapter Hints on installation Before you start What’s in the boxPutting the batteries in the remote CD-R/RW compatibility DVD-R/RW compatibilityCompressed audio compatibility PC-created disc compatibility Before you startAbout WMA Jpeg file compatibilityConnecting up Connecting up ChapterEasy connections Connecting up Connecting using a Scart AV cableConnecting using the S-video output While pressing Connecting using the component video outputTip Connecting to an AV receiverConnecting the digital output Connecting the multichannel analog outputsControls and displays Controls and displays ChapterFront panel Controls and displays Display Controls and displays Remote control Using the remote controlClear Getting started Chapter Switching onUsing the on-screen displays Getting startedGetting started Setting up the player for your Setting the language of this player’s on-screen displaysPlaying discs Press play to start playback Getting startedBasic playback controls Press OPEN/CLOSE to open the disc tray Load a discResume and Last Memory DVD disc menusNumbers Return Video CD/Super VCD PBC menusTOP Menu EnterMy DVD-Audio disc starts playing, but then suddenly stops Playing in slow motion Playing discsPlaying discs Chapter Scanning discsDuring playback, press pause Browsing video content with the Disc NavigatorPlaying discs Frame advance/frame reverse Viewing a Jpeg slideshowSelect a view option Select the thumbnail image for what you want to playUse the cursor buttons Enter to navigate Using repeat play Looping a section of a discTo resume normal playback, select ‘Off’ from the menu Using random play Select a repeat play optionSelect a random play option Creating a program list Mode Searching a discOther functions available from the program menu PlayZooming the screen Playing discs Switching subtitlesSwitching audio language/ channels Switching camera anglesPlaying discs Displaying disc information Audio DRC Audio Settings and Video Adjust menusAudio Settings and Video Adjust menus Chapter Audio Settings menuDialog Audio Settings and Video Adjust menusVideo Adjust menu Make settings using Cursor buttons, and EnterDigital Audio Out settings Initial Settings menuInitial Settings menu Chapter Using the Initial Settings menuInitial Settings menu Video Output settingsMpeg PCM Display settings Initial Settings menu Language settingsSpeakers settings Initial Settings menu Options settingsDTS CD About the audio output settingsSetting/changing the Parental Lock Initial Settings menu Parental LockRegistering a new password Changing your passwordDTS Downmix Audio Output ModeSpeaker Distance Speaker InstallationSpeaker Use Cursor up/down to Change the distance Speaker distance for the highlightedAdditional information Additional information ChapterTaking care of your player and discs Screen sizes and disc formats Additional informationAuto Setting the TV systemResetting the player Power resetAdditional information DVD-Video regions Selecting languages using the language code listAdditional information Language code list Country code listCountry, Country code, Country code letter Additional information Troubleshooting Aspect does not change DVD and CD volume MalfunctionNo picture/No color Screen is stretched orCan’t hear effect OutputSuper VCD disc is not Output properlyAdditional information Digital *1 Additional information GlossaryWMA General Additional information SpecificationsAdditional information Pioneer Corporation
Top Page Image Contents