Pioneer DV-353 Before You Start What’s in the box, Putting the batteries in the remote control

Page 9

Before You Start

What’s in the box

Please confirm that the following accesso- ries are in the box when you open it.

•Remote control

•AA/R6P dry cell batteries x2

•Audio/video cable (red/white/yellow plugs)

•Power cable

•These operating instructions

•Warranty card

Putting the batteries in the remote control

1Open the battery compartment cover on the back of the remote control.

01

•Don’t mix new and old batteries together.

•Don’t use different kinds of battery together—although they may look similar, different batteries may have different voltages.

•Make sure that the plus and minus ends of each battery match the indications in the battery compartment.

•Remove batteries from equipment that isn’t going to be used for a month or more.

•When disposing of used batteries, please comply with governmental regulations or environmental public instruction’s rules that apply in your country or area.

H048 En

2Insert two AA/R6P batteries into the battery compartment following the indications (ª, ·) inside the compart- ment.

3 Close the cover.

Incorrect use of batteries can result in hazards such as leakage and bursting. Please observe the following:

Using the remote control

Keep in mind the following when using the remote control:

•Make sure that there are no obstacles between the remote and the remote sensor on the unit.

•The remote has a range of about 7 meters (23ft.)

•Remote operation may become unreli- able if strong sunlight or fluorescent light is shining on the unit’s remote sensor.

•Remote controllers for different devices can interfere with each other. Avoid using remotes for other equipment located close to this unit.

•Replace the batteries when you notice a fall off in the operating range of the remote.

9

En

Image 9

Contents DV-353DV-251DV-250 Important Safety Instructions Important Notice For U.S. modelFor Canadian model Page Thank you for buying this Pioneer product ContentsSetting/changing the Country Code Initial Settings Menu24-bit/192kHz compatible DAC Before You Start FeaturesPutting the batteries in the remote control Using the remote controlBefore You Start What’s in the box CD-R/RW compatibility Before You Start Discs compatible with this playerCDs and Video CDs are divided into tracks Before You StartConnecting Up Rear panel connections Connecting Up Easy connections Using other types of video output Connecting UpConnecting using an S-Video output Connecting using the component video outputDigital Optical Connecting Up Connecting to an AV receiverConnecting Up Controls and Displays Front panel STANDBY/ONOPEN/CLOSE Controls and Displays Setup Controls and Displays Remote controlAudio SubtitleSurround Play Mode14 0 OPEN/CLOSE AngleGetting Started Switching on Let’s Get StartedPress Enter to move on to the next screen Using the on-screen displays Press Enter again to finish setting upGetting Started Select ‘Setup Navigator’ Setting up with the Setup NavigatorOn-screen display OSD appears Select a DVD languageCongratulations, setup is complete Load a disc Getting Started Playing discsPress 3 play to start playback Press 0 OPEN/CLOSE to open the disc trayBasic playback controls Why won’t the disc I loaded play?Front panel controls DVD-Video disc menusNumbers Video CD PBC menus Playing Discs Introduction Using the Disc Navigator to browse the contents of a discPlaying in slow motion Scanning discsFrame advance/frame reverse To resume normal playback, press PlayLooping a section of a disc Using repeat playPress Enter on ‘BEnd Point’ to set the loop end point Press Enter on ‘AStart Point’ to set the loop start pointSelect a repeat play option Using random playChapter Repeat or Repeat Off Select a random play optionCreating a program list Select ‘Create/Edit’ from the list of program optionsTo add a title, select the title To play the program list, press Play Repeat to build up a program ListEditing a program list Other functions available from the program menuSelect a program play function Create/Edit See above Switching subtitles Switching DVD audio languagePlaying Discs Searching a disc Zooming the screen Switching camera anglesPress Audio repeatly to select an audio channel option Use the cursor buttons to change the zoomed areaPlaying Discs Displaying disc information CD and Video CD displaysMP3 disc displays Virtual Surround Audio Settings Menu Audio DRCAudio Settings Menu Digital Audio Out settings Initial Settings Menu Using the Initial Settings menuDigital Out Dolby Digital OutDTS Out Initial Settings Menu96kHz PCM Out Mpeg OutDefault setting 43 Letterbox Initial Settings Menu Video Output settingsDefault setting S2 TV ScreenDefault setting English Initial Settings Menu Language settingsAudio Language Subtitle LanguageDVD Menu Language Display settingsSubtitle Display OSD LanguageSelect ‘Password’ Angle IndicatorUse the number buttons to enter a 4- digit password OptionsEnter a new password Select ‘Password Change’Use number buttons to enter your password, then press Enter Numbers appear as asterisks as you enter themSelect a new level Select a country code You may also want to refer to the Country code list onThere are two ways you can do this Select ‘Country Code’Handling discs Additional Information Taking care of your player and discsStoring discs Discs to avoidAdditional Information Additional Information Screen sizes and disc formats Resetting the playerWidescreen TV users Standard TV usersCountry code list Additional Information Language code listLanguage Laguage code letter, Language code Country, Country code, Country code letterAnalog audio GlossaryAspect ratio Digital audioMP3 General Additional Information SpecificationsTPTZZ/02A0000 Printed