Arcam P90/3, A90 manual Recording, Record bk, Tape-to-tape copying dubbing

Page 7

Recording

With the Arcam A90 it is possible to listen to and record from one source, or to listen to one source while recording another.

Both sets of tape sockets are identical in sensitivity and suitable for use with almost any type of recorder (cassette, CDR, MD, VCR, reel-to-reel, etc.). The record signal is sent to both the TAPE and VCR output sockets.

RECORD bk

To record the currently selected source, press RECORD until the display shows ‘RECORD SOURCE’. After a few seconds the display reverts to showing the volume level and you are ready to record.

To listen to one source while recording another, press RECORD again until the display shows ‘RECORD’ followed by the name of an input (e.g. ‘AUX’, ‘CD’, ‘TUNER’, etc.). Now press the source selector button on the front panel for the source you wish to record. Your selection is shown on the display for a few seconds, after which it reverts to showing the volume level and you are ready to record.

The RECORD button can also be used as a second zone selector, sending a source signal at line level to a second amplifier operating in another room. If you need help with this, contact your Arcam dealer or Arcam customer support.

Tape-to-tape copying (dubbing)

You can perform tape dubbing from VCR to TAPE, but not from TAPE to VCR.

For example, to copy from a cassette recorder connected to the VCR socket to a cassette recorder connected to the TAPE 1 socket, first use the RECORD button as explained above and select ‘RECORD VCR’. This routes the VCR signal to the TAPE output.

Set the cassette recorder connected to the TAPE socket into its record mode and the other to playback mode to start dubbing.

TAPE 5

To play back the recording from a cassette deck attached to the TAPE 1 input, press TAPE. ‘TAPE 1’ is shown on the display. Selecting this input overrides the other source selectors.

It is also possible to monitor a recording while it is being made, provided your cassette deck is a 3-head type. To do this, press TAPE. Switching this button in/out allows an A/B comparison between the source signal and the recorded signal.

English

A90/P90

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents HANDBOOK/MANUEL/HANDBUCH/HANDLEIDING Important safety instructions Safety guidelinesSafety compliance Safety Using this handbookContents Positioning the unit Installation A90 integrated amplifierConnecting to loudspeakers Connecting to a power supplyStandby power Connecting to other equipmentPre/power amplifier connections Tone Using your A90 integrated amplifierFront panel controls VCRTape RecordingRecord bk Tape-to-tape copying dubbingIntroduction Adjusting listening settings Setting up your A90 integrated amplifierCustomising amplifier settings Enter Using the remote controlCR-389 Remote Control TunerThree channel option Installation P90 power ampliferConnecting to power, loudspeakers and other equipment Remote switchingUsing your P90 power amplifier Bi-wiring your loudspeakers Bi-wiring and bi-amping loudspeakersBefore you start Remote-control codes Power commandsVolume control commands Display control commandsTechnical specifications Service informationOn-line registration Guarantee

A90, P90/3, P90 specifications

The Arcam P90, P90/3, and A90 are prominent models in the Arcam amplifier lineup, renowned for their commitment to delivering high-quality audio performance. Each model showcases advanced technologies aimed at providing an immersive listening experience, catering to audiophiles and casual listeners alike.

The Arcam P90 is a powerful stereo power amplifier that boasts impressive output capabilities. With a dynamic range and high current output, the P90 is designed to drive a wide variety of speakers with ease. The design emphasizes high-performance components and a robust power supply, ensuring that listeners enjoy a clean and detailed sound across the audio spectrum. The P90 also features a proprietary feedback topology, which contributes to its high fidelity and low distortion levels, making it a favorite among professionals and music enthusiasts.

The P90/3 is an enhanced version of the P90, integrating further refinements in performance and efficiency. This model features improvements in power handling and heat dissipation, allowing for sustained performance even during high-demand listening sessions. It maintains the original’s strengths while adding modern connectivity options to accommodate current audio trends. The P90/3 retains the elegant design language synonymous with Arcam products, featuring a sturdy chassis that minimizes vibrations and interference, thereby enhancing sound quality.

The A90, part of the same family, is a highly regarded integrated amplifier that incorporates both rugged amplification and versatile inputs. With a focus on user-friendly operation, the A90 allows direct connection with various sources, including digital and analog devices. It features advanced digital-to-analog conversion technology, ensuring pristine audio playback regardless of source quality. The A90 also emphasizes high current delivery, thus enabling it to produce a rich, dynamic soundstage that captivates listeners.

All three models share Arcam's dedication to high-quality engineering, with a focus on reducing distortions and enhancing audio clarity. Their compatibility with a wide array of audio formats ensures that they remain relevant in an ever-evolving digital landscape. With features that prioritize performance, durability, and aesthetic appeal, the Arcam P90, P90/3, and A90 amplifiers stand out as top choices for anyone serious about their audio experience, providing the fidelity and emotional engagement that audiophiles crave.
Top Page Image Contents