Silvercrest KH6519 operating instructions Audio settings

None:

Off:

On:

PCM:

RAW:

Off:

10.3.3Adjusting the video-output using the buttons of the remote control

You can also directly adjust the video-output for RGB format, Progressive- Scan format and HDMI format using the buttons on the remote control. The buttons are marked as follows:

HDMI	HDMI format
YUV	Progressive-Scan format
RGB	RGB format

Attention!

In the event that you set an incorrect Video output, for example "P-Scan", alt- hough your television is not capable of Progressive Scan, then the television screen will suddenly become black.

This is not a defect of the television or the DVD player!

In this case press the STOP￿ button on the front panel of the DVD player or on the remote control.

Then press the VIDEO button on the remote control continuously until an image appears again on the television screen.

Brightness: Here, with the control buttons , you set the brightness value (1-16) of the DVD player.

Sharpness: Here, with the control buttons , you set the contrast value (1-16) of the DVD player.

HD-Resolution: Here you can select from several resolutions for the HDMI output. Check, using the playback device's instruction manu- al, which resolutions (480p/576p/720p/1080i/1080p/Auto) are supported. In the setting Auto, the resolution supported by the television set is utilised.

HD-JPEG mode: Here you can select from several resolutions for the image display via the HDMI Output.

10.4 Audio settings

In this OSD menu you can administer the settings for Bass Management, the Speaker size of individual loud speakers, Test sound, Delays, Digital audio outputs , Night mode and ProLogic.

Note:

The input Front Speakers can not be deactivated since sound output for the front speakers is always switched on.

Subwoofer: Set this entry to Present when a subwoofer is connected and is to be activated.

In order to deactivate this sound output set the entry to None.

Test tones: Here you can switch on a test sound for each particular audio output in order to check your 5.1 Surround settings.

Surround

Center,

delay:Here you set the delay for the centre and rear surround loud- speakers. Each increase of the distance setting corresponds to a delay of one millisecond. With optimal settings the sound reaches your ears simultaneously from all directions. Center: No delay, 0.3, 0.6, 1, 1.4, 1.7 m

Surround: No delay, 1, 2, 3, 4 or 5.1 m

Digital Output: here you set the DVD players digital output signal. No digital audio component connected

Two channel digital audio component connected via coaxial cable or optical cable.

Multi channel digital audio component, i.e. DTS receiver, connected via coaxial cable or optical cable.

Night Mode: Here you activate/deactivate the night mode. This setting facilitates an optimal sound playback with reduced volu- me. The loud passages are suppressed and the quieter passages are played back a little louder. This function is only possible when using a digital audio component.

Pro Logic: Here you set the Dolby ProLogic compatibility.

No Dolby Prologic compatible audio component is connected to the analogue stereo output (L/R). A Dolby Prologic compatible audio component is connected to the analogue stereo output (L/R) of the DVD player.

Bass

management: Here you can Activate/Deactivate the Bass-Management. Activation (On) is necessary if you are not using a 5.1 am- plifier with its own speaker management but rather want the sound output transmitted via a particular amplifier. In this case the DVD player must be informed which kind of speaker (Small/Large) is to be run from the respective sound output. In this way the sound and the separation of Highs, Middles and Basses can be optimally conformed.

Front LS,

Center LS,

Surround LS: Here you can Activate/Deactivate the particular speaker type and set the size.

Large: Activate sound output for large speakers.

Small: Activate sound output for small speakers. (only with the activation of Bass-Management) Deactivate sound output for these types of speakers

- 12 -