Lanzar Car Audio 15 f e a t u r e s a n d s p e c i f i c a t i o n s, Control Frequencies, 100dB

f e a t u r e s a n d s p e c i f i c a t i o n s

1.Fader Control This rotary controls the balance between the front and rear outputs. This fader takes priority over the fader in your car stereo head unit.

2.Right and Left Channel Equalizer The 15 band equalizer controls divide the frequency control range into 1/2 octave steps at Controls 20Hz, 30Hz, 45Hz, 67Hz, 100Hz, 150Hz, 200Hz, 350Hz, 500Hz,800Hz,and at full octave

steps, 1100Hz, 2200Hz, 4400Hz, 8800Hz, 17200Hz. Each rotary control permits the signal at that control’s frequency to be either increased (by turning clockwise) or decreased (by turning counter-clockwise) by up to 12 dB. When set to the center detent position, the control provides no increase or decrease at that frequency.

3.Right and Left Output Level Controls There are separate level controls on the E-15 for both the left and right channel outputs. When installing and first setting up the system, set the output level controls to the center detent position for a starting point.

Typically, when the head unit volume is set to approximately the 2 o’clock position your system is at its ideal volume. Set the head unit volume this way, and then adjust the outputs on the E-15 accordingly to achieve the ideal volume without over-driving the inputs of your amplifier, which will create distortion.

The goal in the adjustment is to obtain the best signal-to-noise ratio while obtaining your desired listening volume.

4.EQ In/Out Switch This switch controls whether or not the E-15 is providing equalization (”IN”) or simply passing signals through in an unaffected way.

5.Line Inputs The line inputs are connected to your head units RCA outputs. If your head unit has a fader that fades between two sets of RCA outputs make sure that the head unit fader is turned toward the set of RCA connectors that you are using. If your radio has only speaker level outputs you can connect the E-15 to your head unit via a high/low level adapter (for example, a Pyramid NS-60 or equivalent). This separate component allows you to connect your speaker wires from your head unit and the RCA cables from the E-15 while balancing the head unit’s output and the equalizer’s input.

6.Front & Rear Outputs Connect these outputs to the appropriate inputs of your power amplifier(s). The front outputs connect to the amplifier driving your front speakers, the rear outputs for the rear amplifier.

7.Line Outputs Connect this output to another signal processor type device in your system, such as a

crossover. Th1s line output level is unaffected by the fader control.

8.Power Indicator This indicator lights up when the internal power supply is activated and the unit is operational.

Control Frequencies
Half Octave	20Hz • 30Hz • 45Hz • 67Hz
	100Hz • 150Hz • 200Hz
	350Hz • 500Hz • 800Hz
Full Octave	1.1KHz • 2.2KHz
	4.4KHz • 8.8KHz • 17.2KHz
Control Range	12dB Boost/Cut
Frequency Response	10Hz - 30KHz	5
Signal-to-Noise Ratio (A-Wtd)	100dB
Input Sensitivity	80mv-2.0Volts
	for 400mv Output
Maximum Output Voltage	7.0 Volts
Channel Separation	65 dB
Power Requirement	11-16 Volts DC
	negative ground
Dimensions, WxDxH, inches	11-5/8 x 8-9/32	x 1-1/2
(millimeters)	(295 x 210 x 38)

Lanzar strives to continually improve and refine its products, as well as to design new models. Therefore, the product specifications and illustrations in this manual are subject to change without notice.