Samsung CL-29Z40DS, CL-32Z40DS, CL-32Z30DS manual Connections, Connecting VHF and UHF Antennas

Page 8

Installing Batteries in the Remote Control

1.Lift the cover at the back of the remote control upward as shown in the figure.

2. Install two AAA size batteries.

➢ Make sure to match the “+” and “–” ends of the batteries with the diagram inside the compartment.

3.Replace the cover.

➢Remove the batteries and store them in a cool, dry place if you won’t be using the remote control for a long time. The remote control can be used up to about 23 feet from the TV.

(Assuming typical TV usage, the batteries last for about one year.)

➢If the remote control doesn’t work, check the following:

1.Is the TV power on?

2.Are the plus and minus ends of the batteries reversed?

3.Are the batteries drained?

4.Is there a power outage, or is the power cord unplugged?

5.Is there a special fluorescent light or neon sign nearby?

Connections

Connecting VHF and UHF Antennas

If your antenna has a set of leads that look like this, see “Antennas with 300 Ω Flat Twin Leads” below.

If your antenna has one lead that looks like this, see “Antennas with 75 Ω Round Leads”.

If you have two antennas, see “Separate VHF and UHF Antennas”.

Antennas with 300 Ω Flat Twin Leads

If you are using an off-air antenna (such as a roof antenna or “rabbit ears”) that has 300 Ω twin flat leads, follow the directions below.

1. Place the wires from the twin leads under the screws on a 300-75 Ω adapter (not supplied).

Use a screwdriver to tighten the screws.

2. Plug the adaptor into the ANT 1 IN (AIR) terminal on the back of the TV.

Antennas with 75 Ω Round Leads

1. Plug the antenna lead into the ANT 1 IN (AIR) terminal on the back of the TV.

Separate VHF and UHF Antennas

If you have two separate antennas for your TV (one VHF and one UHF), you must combine the two antenna signals before connecting the antennas to the TV. This procedure requires an optional combiner-adaptor (available at most electronics shops).

UHF VHF

1.Connect both antenna leads to the combiner.

UHF VHF

2.Plug the combiner into the ANT 1 IN (AIR) terminal on the back of the TV.

English-8

Image 8

Contents Owner’s Instructions English-2 Contents General Information List of FeaturesAccessories Power Indicator Remote Control SensorViewing the Control Panel Buttons on the Lower-Right Part of the PanelUpgrade Port USB For service only Viewing the Connection PanelRear Panel Jacks Side Panel JacksRemote Control Installing Batteries in the Remote Control Connecting VHF and UHF AntennasIf the remote control doesn’t work, check the following ConnectionsConnecting Cable TV Connecting to a Cable Box that Descrambles All ChannelsConnecting to a Cable Box that Descrambles Some Channels Cable without a Cable BoxConnecting a VCR Connecting an S-VHS VCRConnecting a Second VCR to Record from the TV Connecting a CamcorderConnecting a DVD Player/Set-Top Box English-11Connecting a DVD Player/Set-Top Box via Hdmi Connecting a Digital Audio SystemConnecting an Amplifier/DVD Home Theater Plug & Play FeatureOperation Turning the TV On and OffSetting the Clock Automatically TV will begin memorizing all of the available channelsClock Mode. menu is automatically displayed Press the Enter buttonChanging Channels Adjusting the Volume Using Mute ButtonViewing the Display Viewing the MenusSelecting the Video Signal-source Memorizing the ChannelsStoring Channels in Memory Automatic Method English-17Setting Up the Remote control to Operate Your Cable Box Setting Up Your Remote ControlSetting Up the Remote control to Operate Your VCR Setting Up the Remote control to Operate Your DVD Setting Up the Remote control to Operate Your Set Top BoxRemote Control Codes Brand CodeProduct Code 000 001 BD Record 005007 008 009 010 VCR Record 012To Select the Source To Edit the Input Source NameEnglish-23 Source ListUsing Automatic Picture Settings Picture ControlEnglish-24 PictureResetting the Picture Settings to the Factory Defaults Viewing with a 43 signal When a 43 signal is receivedChanging the Screen Size Screen size selection depends on the type of video inputSetting the Film Mode Using Automatic Sound SettingsSound Control TiltSetting the SRS TruSurround XT Sound Balance AdjustmentBandwidth Adjustment 100Hz, 300Hz, 1KHz, 3KHz, 10KHz Customizing the SoundAutomatic Volume Control Reduces the differences in volume level among broadcastersChoosing a Multi-Channel Sound MTS track Digital Preferred LanguageSetting the On/Off Melody Choosing a Multi-Channel Sound MTS track AnalogMulti-Track Sound English-29Channel Control Selecting the AntennaAdding and Erasing Channels English-30English-31 To set-up Your Favorite ChannelsYou can set channels you watch frequently as favorites English-32 Setting the Default Channel List ModeViewing the Channel Lists Fine Tuning Analog Channels Labeling ChannelsPress the Menu button to display the menu English-33Checking the Digital-Signal Strength Using the R.Surf FeatureSignal Strength English-34English-35 Time SettingSetting the Time Option 2 Setting the Clock Automatically Setting the On/Off TimerEnglish-36 Time ZoneEnglish-37 Setting the Sleep TimerTo cancel the set sleep timer Function Description Selecting a Menu LanguageViewing Closed CaptionsOn-Screen Text Messages Digital Digital Captions function operates on digital channelsEnglish-39 Caption OptionsViewing Closed CaptionsOn-Screen Text Messages Analog English-40English-41 Setting the Blue Screen ModeMenu Transparency Level English-42 Setting the Function HelpDisplays help on the menu functions Identifying Problems SpecificationsProblem Possible Solution AppendixContact Samsung WORLD-WIDE