Samsung HP-P4271 manual How to Adjust Mounting Angle, Factory default, Change Angle

Page 13

Secure the SET to the wall mount bracket. (Please refer to the following instructions.)

How to Adjust Mounting Angle

Note: Please secure the mounting bracket on the wall surface after setting its angle at 0°.

Factory default

How to Adjust Mounting Angle

Please tighten the captive screw in the direction of the arrow after assembling the bracket.

Hold onto the middle of the PDP to adjust the angle (not the sides of the PDP).

Change Angle

1

Set the angle by pulling the upper end of the SET attached

2to bracket in the direction of the arrow.

3 The angle can be adjusted from 0° to 15° by ±2°.

Connecting External Devices to the PDP

Be sure to remove the safety pins underneath the PDP.

1 (Caution : If the safety pins are not removed, the angle cannot be adjusted.) Any attempt to do so may cause damage to the PDP.

Hold onto the bottom of the PDP and pull forward fully as

2directed by the arrow(as illustrated) to adjust the angle. (0°~20° by 2°). Insert the Safety Pins to the front guide holes on both sides as illustrated in figure ´.

3 Viewing the PDP after connecting the external devices. Remove the Safety Pins to adjust the angle to 0°, then secure the Safety Pins again. (Warning : For safety, be sure to secure the PDP using the safety pins. If the safety pins are not used, the PDP may fall, causing serious injury.)

Notes

•Contact an authorized technician when installing the wall attachment panel.

•After hanging the PDP panel on the wall attachment panel, make sure that the Insulation holders are completely hung.

•Be careful not to get your fingers caught during installation.

•Make sure the wall attachment panel brackets are tightened. Otherwise, the PDP panel may fall down.

•Please secure the mounting bracket on the wall surface after setting its angle at 0°.

13

Image 13

Contents Owner’s Instructions Page User Instructions Table of Contents General Information Remote Control Signal Receiver Power IndicatorSpeakers Source buttonAudio Input L, R Ferrite Cores Only for Service´ Anynet Monitor OUT Video / L-AUDIO-RRemote Control Buttons Remote Control Operation Range ∑ Reset button¸ SRS Tsxt button ˛ MTS buttonWall Mount Bracket Installation NotesSupport Bars Screws How to assemble the Wall Mount Bracket Fixing the PDP panel to the wall attachment panel bracket Factory default How to Adjust Mounting AngleConnecting External Devices to the PDP Change AngleParts Installing the SpeakersSpeakers Speaker Dust Cover Speaker CableBlack How to Assemble the Speakers Wall Mount Black How to assemble the Stand-Base Connections Antennas with 75-ohm Round Leads Connecting VHF and UHF AntennasCable without a Cable Box Connecting Cable TVPage Videotape Playback Connecting a VCRViewing camcorder tapes Connecting a CamcorderViewing Tapes Playing DVD Connecting a DVD Player 480i, 480pTo Play DVD To Watch DTV Watching DTVOperation Viewing the Menus and Displays Turning the PDP On and OffViewing the Menus Displaying Status Information Press the Enter button to confirm your choice Plug & Play FeatureEnjoy your watching Plug and Play can only be accessed in the TV mode Memorizing the Channels Selecting the Video Signal-sourceStoring Channels in Memory Automatic Method Adding and Erasing Channels Manual Method To View Memorized Channels PIP Mode Using Mute Adjusting the VolumeChanging Channels Setting Up Your Remote Control Remote Control Codes Setting the Signal Source Viewing an External Signal SourceAssigning Names to External input mode Page Picture Control PIP Customizing the PictureUsing Automatic Picture Settings Selecting the Color Tone DNIe Digital Natural Image engine Changing the Screen Size Panorama 169WideZoom 3NormalStill Freezing the PictureSelecting the PIP Screen Viewing the Picture-in-PictureSelecting an External Signal Swapping the Contents of the PIP and Main Image Changing the Size of the PIP Window Changing the Location of the PIP Image Selecting a Signal Source Antenna or Cable for PIP Changing the PIP Channel Setting the My Color Control Mode Green Pink My Color Control Mode CharacteristicsMy Color Control Custom Settings Setting the My Color Control ModeMove Enter Return Page Sound Control Customizing the Sound Using Automatic Sound Settings Choosing a Multi-Channel Sound MTS Soundtrack Using the Auto Volume TruSurround XT, SRS and Symbol Setting the TruSurround XTListening to the Sound of the SubPIP Picture Selecting the Internal Mute Channel Control Fine Tuning Channels LNA Low Noise Amplifier Page Connecting a PC and Operation To watch the PC screen Connecting a PCSetting up Your PDP Plug and Play Pin ConfigurationSub Cable How to Set up Your PC Software Windows only IBM PC / AT Adjusting the R.G.B Adjusting the PC ScreenChanging the Position of the Image Picture Automatic Adjustment Picture Quality AdjustmentCoarse Adjustment Fine Tuning Fine Information Page Time Setting Setting the Clock Setting the Sleep Timer Setting the Timers Air Page Function Description Selecting a Menu Language Digital Noise Reduction Selecting the Film Mode Using the Color Weakness Enhancement Option Setting the Melody Sound Setting the Blue Screen Selecting the Fan Viewing Closed Captions Setting Up Your Personal ID Number PIN Using the V-ChipHow to Enable/Disable the V-Chip How to Set up Restrictions using the TV Parental Guidelines 105 106 107 Page Appendix Problem TroubleshootingIdentifying Problems Care and MaintenanceTemperature LiquidsVideo input SpecificationsMemo 114 115 BN68-00757A-00