Samsung HP-P4261 manual How to Adjust Mounting Angle, Factory default, Change Angle

Page 13

Secure the SET to the wall mount bracket. (Please refer to the following instructions.)

BN68-00678A-01_002~23 2004.4.28 6:12 PM Page 13

How to Adjust Mounting Angle

Notice : Please secure the mounting bracket on the wall surface after setting its angle at 0°.

Factory default

How to Adjust Mounting Angle

Please tighten the captive screw in the direction of the arrow after assembling the bracket.

Hold onto the middle of the PDP to adjust the angle (not the sides of the PDP).

Change Angle

1

Set the angle by pulling the upper end of the SET attached

2to bracket in the direction of the arrow.

3 The angle can be adjusted from 0° to 15° by ±2°.

Connecting External Devices to the PDP

Be sure to remove the safety pins underneath the PDP.

1 (Caution : If the safety pins are not removed, the angle cannot be adjusted.) Any attempt to do so may cause damage to the PDP.

Hold onto the bottom of the PDP and pull forward fully as

2directed by the arrow(as illustrated) to adjust the angle. (0°~20° by 2°). Insert the Safety Pins to the front guide holes on both sides as illustrated in figure ´.

3 Viewing the PDP after connecting the external devices. Remove the Safety Pins to adjust the angle to 0°, and then secure the Safety Pins again. (Warning : For safety, be sure to secure the PDP using the safety pins. If the safety pins are not used, the PDP may fall, causing serious injury.)

Note

•Contact an authorized technician when installing the wall attachment panel.

•After hanging the PDP panel on the wall attachment panel, make sure that the Insulation holders are completely hung.

•Be careful not to get your fingers caught during installation.

•Make sure the wall attachment panel brackets are tightened. Otherwise, the PDP panel may fall down.

•Please secure the mounting bracket on the wall surface after setting its angle at 0°.

13

Image 13

Contents Owner’s Instructions User Instructions WarrantyScreen Image retention Cell DefectTable of Contents BN68-00678A-01002~23 2004.4.28 612 PM General Information Power Indicator Speakers Remote Control Signal ReceiverSource button Menu buttonPC Input RGB in / Audio Video Input Audio Input L, RVIDEO1, S-VIDEO2 AV1, AV2, AV3Remote Control Buttons Remote Control Operation Range ∑ Reset button¸ SRS Tsxt button ˛ MTS buttonInstallation Notes Wall Installation InstructionsWall Mount Bracket Support Bars ScrewsHow to assemble the Wall Mount Bracket Fixing the PDP panel to the wall attachment panel bracket Factory default How to Adjust Mounting AngleConnecting External Devices to the PDP Change AngleHow to assemble the Stand-Base Connections Antennas with 75-ohm Round Leads Connecting VHF and UHF AntennasCable without a Cable Box Connecting Cable TVBN68-00678A-01002~23 2004.4.28 612 PM Videotape Playback Connecting a VCRViewing camcorder tapes Connecting a CamcorderViewing Tapes Playing DVD Connecting a DVD Player 480i, 480pTo Play DVD Watching DTV Connecting a DTV ReceiverTo Watch DTV Operation Turning the PDP On and Off Turning the PDP On and OffViewing the Menus and Displays Viewing the MenusDisplaying Status Information Press the Enter button to confirm your choice Plug & Play FeatureEnjoy your watching Plug and Play can only be accessed in the TV mode Memorizing the Channels Selecting the Video Signal-sourceStoring Channels in Memory Automatic Method Adding and Erasing Channels Manual Method To View Memorized Channels PIP Mode Using Mute Adjusting the VolumeChanging Channels Setting Up Your Remote Control Remote Control Codes Setting the Signal Source Viewing an External Signal SourceAssigning Names to External input mode BN68-00678A-01024~65 2004.4.28 614 PM Picture Control PIP Customizing the PictureUsing Automatic Picture Settings Selecting the Color Tone Press the or button to select DNIe, then press Enter button DNIe Digital Natural Image engineChanging the Screen Size Panorama 169WideZoom 3NormalStill Freezing the PictureSelecting the PIP Screen Viewing the Picture-in-PictureSelecting an External Signal Swapping the Contents of the PIP and Main Image Changing the Size of the PIP Window Changing the Location of the PIP Image Selecting a Signal Source Antenna or Cable for PIP Changing the PIP Channel Using the MCC Function in the Easy Control Menu Setting the MCCMy Control Color ModeEmerald Green Indian Pink MCC Mode CharacteristicsMCC Custom Settings Resetting the MCC Colors to the Factory Defaults BN68-00678A-01024~65 2004.4.28 615 PM Sound Control SRS Tsxt Customizing the SoundUsing Automatic Sound Settings Choosing a Multi-Channel Sound MTS Soundtrack Using the Auto Volume TruSurround XT, SRS and Symbol Setting the TruSurround XTListening to the Sound of the SubPIP Picture Selecting the Internal Mute Channel Control Fine Tuning Channels LNA Low Noise Amplifier BN68-00678A-01066~81 2004.4.28 618 PM Connecting a PC and Operation To watch the PC screen Connecting a PCSetting up Your PDP Plug and Play Pin ConfigurationSub Cable How to Set up Your PC Software Windows only IBM PC / AT Adjusting the R.G.B Adjusting the PC ScreenChanging the Position of the Image Picture Automatic Adjustment Picture Quality AdjustmentCoarse Adjustment Fine Tuning Fine Information BN68-00678A-01082~103 2004.4.28 623 PM Time Setting Setting the Clock Setting the Sleep Timer Setting the Timers Air Off BN68-00678A-01082~103 2004.4.28 623 PM Function Description Selecting a Menu Language Digital Noise Reduction Selecting the Film Mode Using the Color Weakness Enhancement Option Setting the Melody Sound Setting the Blue Screen Selecting the Fan Viewing Closed Captions Setting Up Your Personal ID Number PIN Using the V-ChipHow to Enable/Disable the V-Chip TV-MA How to Set up Restrictions using the TV guidelines101 102 103 BN68-00678A-01104~111 2004.4.28 626 PM Appendix Problem Possible Solution TroubleshootingIdentifying Problems Care and MaintenanceTemperature LiquidsVideo input SpecificationsMemo 110 111 BN68-00678A-01