Samsung LC540-ZC, BN68-02756B-04 Listening through a Receiver, Troubleshooting for Anynet+

¦¦ Listening through a Receiver

You can listen to sound through a receiver (i.e Home Theater) instead of the TV speaker.

1.Select Receiver and set to On.

2.Press the EXIT button to exit.

✎✎ If your receiver supports audio only, it may not appear in the device list.

✎✎ The receiver will work when you have properly connected the optical in jack of the receiver to the DIGITAL AUDIO OUT (OPTICAL) jack of the TV.

✎✎ When the receiver (i.e Home Theater) is set to On, you can hear sound output from the TV’s Optical jack. When the TV is displaying a DTV (air) signal, the TV will send out 5.1 channel sound to the receiver. When the source is a digital component such as a DVD and is connected to the TV via HDMI, only 2 channel sound will be heard from the receiver.

✎✎NOTE

xx You can only control Anynet+ devices using the TV remote control, not the buttons on the TV.

xx The TV remote control may not work under certain conditions. If this occurs, reselect the Anynet+ device. xx The Anynet+ functions do not operate with other manufacturers’ products.

¦¦ Troubleshooting for Anynet+

Problem	Possible Solution
Anynet+ does not work.	• Check if the device is an Anynet+ device. The Anynet+ system supports Anynet+ devices only.
	• Only one receiver (home theater) can be connected.
	• Check if the Anynet+ device power cord is properly connected.
	• Check the Anynet+ device’s Video/Audio/HDMI cable connections.
	• Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.
	• Check whether the TV remote control is in TV mode.
	• Check whether the remote control is Anynet+ compatible.
	• Anynet+ does not work in certain situations. (Searching channels, operating Media Play or Plug & Play
	(initial setup), etc.)
	• When connecting or removing the HDMI cable, please make sure to search devices again or turn your
	TV off and on again.
	• Check if the Anynet+ Function of Anynet+ device is set on.
I want to start Anynet+.	• Check if the Anynet+ device is properly connected to the TV and check if the Anynet+ (HDMI-CEC) is
	set to On in the Anynet+ Setup menu.
	• Press the TOOLS button to display the Anynet+ menu and select a menu you want.
I want to exit Anynet+.	• Select View TV in the Anynet+ menu.
	• Press the SOURCE button on the TV remote control and select a device other than Anynet+ devices.
	• Press > CH <, CH LIST, PRE-CH, and FAV.CH to change the TV mode. (Note that the channel
	button operates only when a tuner-embedded Anynet+ device is not connected.)
The message ‘Connecting to	• You cannot use the remote control when you are configuring Anynet+ or switching to a view mode.
Anynet+ device...’ appears on	• Use the remote control when the Anynet+ setting or switching to view mode is complete.
the screen.
The Anynet+ device does not	• You cannot use the play function when Plug & Play (initial setup) is in progress.
play.
The connected device is not	• Check whether or not the device supports Anynet+ functions.
displayed.	• Check whether or not the HDMI cable is properly connected.
	• Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.
	• Search Anynet+ devices again.
	• You can connect an Anynet+ device using the HDMI cable only. Some HDMI cables may not support
	Anynet+ functions.
	• If it is terminated by an abnormal situation such as disconnecting the HDMI cable or power cord or a
	power failure, please repeat the device scan.
The TV Program cannot be	• Check whether the antenna jack on the recording device is properly connected.
recorded.
The TV sound is not output	• Connect the optical cable between TV and the receiver.
through the receiver.

04 Advanced Features

English 31