Quick Setup Guide
Step 4 : Connect External Devices
Congratulations on the purchase of your new Samsung TV. Read this setup guide to get your TV up and running quickly.
STOP |
| |
| ||
| Samsung Electronics America, Inc. | |
Please do not return this unit. | 85 Challenger Road Ridgefield Park, NJ | |
If you have problems operating your | Samsung Electronics Canada Inc. | |
TV, call: | ||
55 Standish Court Mississauga, Ontario L5R 4B2 | ||
For web support please visit: | Call Center hours of operation: | |
www.samsung.com/support | ||
To register this product, visit : www.samsung.com/register. | ||
|
Getting Started
Step 1 : Install the Stand
Follow the steps below to connect the TV to the stand.
✎✎ Make sure to distinguish between the front and back of the Stand and Guide Stand when assembling them.
✎✎ Make sure that at least two people lift and move the LCD TV.
✎✎ Lay the product down, with the screen facing up and fasten the screws.
1
Connecting an AV device
For the very best picture quality, select HD signal sources and use HDMI cables and connections. Note that many digital cable programs are not in HD. Check with your video provider to ensure your are receiving HD signals.
The HDMI connection carries digital video and audio.
Audio/Video connection (480i only)
Using an Audio/Video Cable
VIDEO OUT | AUDIO OUT | VCR |
HD connection (up to 1080p)
Using an HDMI Cable
HDMI OUT |
| Device |
|
|
|
DVD /
Best Connection
HD connection (up to 1080p)
Using an DVI to HDMI Cable
DVI OUTDevice
AUDIO OUT | DVD / | |
Cable Box / | ||
| ||
| Satellite receiver (STB) |
Very Good Connection
Component connection (up to 1080p)
Using a Component Cable
AUDIO OUT COMPONENT OUT | Device |
VCR / DVD /
Good Connection
Connecting an audio device
Connect your TV to your Home Theater or other audio | Analog Audio connection | ||
device to enjoy enhanced sound quality. | Using an Audio Cable | ||
| |||
| AUDIO IN |
| Device |
|
|
|
|
Amplifier / DVD Home Theater
Digital Audio connection
Using an Optical Cable
Digital Audio System
OPTICAL
Connecting a PC |
|
| ||
Connect your TV to a PC to use it as a Monitor. |
| HD connection | ||
|
|
|
| |
|
|
|
| Using an HDMI Cable |
|
|
|
| AUDIO OUT DVI OUT |
|
|
|
| |
|
|
|
| |
|
|
|
| PC |
Using an D-Sub Cable
2
Stand
|
| ✎✎ | When connecting to AV IN on the back of your TV, attach the video | |
VCR / DVD / | cable (yellow) to the green jack next to the AV In 1 label. The jack will | |||
not match the color of the video cable (yellow). | ||||
Satellite receiver | ||||
Lowest Quality Connection |
| |||
PC OUT | AUDIO OUT |
PC
Screw
Step 2 : Install the Batteries into the Remote
To install batteries into your remote control, follow these steps:
1.Lift the cover on the back of the remote upward
as shown in the figure to the right.
2.Install two AAA batteries.
✎✎ Make sure to match the + and - ends of the batteries to the diagram in the battery compartment.
3.Replace the cover.
Step 3 : Connect Power and Antenna or Cable
|
|
|
|
| Connect Ant In to: |
|
|
|
|
| |
|
|
|
|
| • Wall cable jack or |
|
|
|
|
| |
|
|
| or | ||
|
|
| • VHF/UHF | ||
Power Input |
|
|
|
| Antenna or |
|
|
|
| ||
|
|
|
| • Cable or Satellite | |
| |||||
| Use a 75 ohm (round) cable. | box Ant or Cable | |||
| Out | ||||
Make sure the AC power cord is plugged in securely to the wall outlet and the TV.
Step 5 : Run Plug & Play
When you turn on your TV for the first time, it automatically launches the Plug & Play function. With Plug & Play, you can select the On Screen Display language, set the clock mode, and launch the TV’s channel memorizing process. It also displays connection instructions similar to those in this guide.
To navigate while Plug & Play is running, press the Up, Down, Left or Right arrow buttons on your remote. To make a selection, press the EnterEbutton. To skip a screen, press the Menu button.
To turn on your TV, press the Power button on the remote or press the Power button on the TV. To run Plug & Play, follow these steps:
| Plug & Play | |||||
|
|
|
| |||
Select Language of the OSD. |
|
|
|
| ||
|
|
|
| |||
| English |
|
| |||
Language | : | Español |
| |||
Français |
| |||||
|
|
| ||||
|
|
| UMove EEnter | |||
1.On the Language screen, select the language for the On Screen Display (OSD) using your remote control, and then press EnterEbutton. The Home Use screen appears.
2.Select Home Use, and then press EnterEbutton. If you select Store Demo, the TV will reset your picture and audio settings every 30 minutes. After you press EnterEbutton, the Antenna Source screen appears.
3.If your TV is only attached to an antenna, select Air. If your TV is only attached to cable and you have no cable box, select Cable. If your TV is attached to an antenna and cable with no box, select Auto. When done, press EnterEbutton on your remote. The Select Cable System screen appears.
IMPORTANT: If your TV is attached to a cable or satellite box, skip Steps 3 through 5. After Plug & Play is complete, set your TV to Channel 3 or 4, according to the directions for your cable or satellite box.
4.If your TV is attached to a cable system and you have no cable box, you must select your cable system type. If you have Digital cable, you must select the cable system type for both Analog and Digital. After you have selected the cable system type, select Start, and then press the EnterEbutton on your remote.
✎✎ Most cable systems are Standard (STD) systems. If you are not sure about what kind of cable system you have, contact your cable company.
5.The TV memorizes the available channels. This process can take up to 45 minutes. After the TV has memorized the channels, the Clock Mode screen appears.
6.Choose the Clock Mode. Select Auto if you have a digital channel in your area. Select Manual if you don’t, or if you have a cable or satellite box. When done, press EnterEbutton. The Daylight Savings screen appears.
✎✎ If you select Manual, the clock setting screen appears.
7.Select the Daylight Saving Time setting: Off, On, or Auto, and then press EnterEbutton.
8.After the time zone screen, The connection method for best HD screen quality is displayed. Press Right arrow button on your remote to view each screen in succession. Press the Blue button to skip this section.
9.The Enjoy your TV screen appears. and then press EnterEbutton.
Basic Functions
Changing the Screen Size
Your TV has several screen size options, each designed to work best with specific types of video input. If you have a cable box or satellite receiver, it may have its own set of screen sizes as well.
To change the screen size, press the P.Size button on your remote. The first time you press it, your TV displays the current setting. Thereafter, each time you press the P.Size button, you change the size of the picture on the screen.
The following sizes are available:
16:9 Wide screen | Zoom 1 | Zoom 2 |
Wide Fit | 4:3 Standard screen | Screen Fit |
✎✎ Screen Fit displays a full HD picture covering the entire screen with no cutoff on any side. It is only available when your TV inputs an HDMI (720p, 1080i, 1080p), Component (1080i, 1080p), or DTV
English - 1