Quick Setup Guide
Step 4 : Connect External Devices
Congratulations on the purchase of your new Samsung TV. Read this setup guide to get your TV up and running quickly.
STOP |
| |
| Samsung Electronics America, Inc. | |
Please do not return this unit. | 105 Challenger Road Ridgefield Park, NJ | |
If you have problems operating your | Samsung Electronics Canada Inc. | |
TV, call: | ||
55 Standish Court Mississauga, Ontario L5R 4B2 | ||
For web support please visit: | Call Center hours of operation: | |
www.samsung.com/support | ||
To register this product, visit : www.samsung.com/register. | ||
|
Getting Started
Step 1 : Install the Stand
Connecting an AV device
For the very best picture quality, select HD signal sources and use HDMI cables and connections. Note that many digital cable programs are not in HD. Check with your video provider to ensure your are receiving HD signals.
The HDMI connection carries digital video and audio.
HD connection (up to 1080p)
Using an HDMI Cable
HDMI OUT |
| Device |
|
|
|
DVD /
Best Connection
HD connection (up to 1080p)
Using an DVI to HDMI Cable
AUDIO OUTDevice
Connecting an audio device
Connect your TV to your Home Theater or other audio device to enjoy enhanced sound quality.
Analog Audio connection
Using an Audio Cable
AUDIO IN |
| Device |
|
|
|
Amplifier / DVD Home Theater
Digital Audio connection
Using an Optical Cable
Digital Audio System
OPTICAL
Follow the steps below to connect the TV to the stand.
✎✎ Make sure to distinguish between the front and back of the Stand and Guide Stand when assembling them.
✎✎ Make sure that at least two people lift and move the LCD TV.
✎✎ Lay the product down, with the screen facing up and fasten the screws.
1
DVI OUT | DVD / | |
Cable Box / | ||
| ||
| Satellite receiver (STB) |
Very Good Connection
Connecting a PC |
|
Connect your TV to a PC to use it as a Monitor. | HD connection |
| |
| Using an |
| PC OUT AUDIO OUT |
2
Component connection (up to 1080p)
Using a Component Cable
AUDIO OUT COMPONENT OUT | Device |
VCR / DVD /
Good Connection
PC
Using an HDMI Cable
AUDIO OUT | DVI OUT |
PC
Stand
Screw
Step 2 : Install the Batteries into the Remote
To install batteries into your remote control, follow these steps:
1.Lift the cover on the back of the remote upward
as shown in the figure to the right.
2.Install two AAA batteries.
✎✎ Make sure to match the + and - ends of the batteries to the diagram in the battery compartment.
3.Replace the cover.
Step 3 : Connect Power and Antenna or Cable
Connect Ant In to:
|
| • Wall cable jack or | |
|
| • VHF/UHF | |
|
| Antenna or | |
or | |||
• Cable or Satellite | |||
|
| box Ant or Cable | |
|
| ||
|
| Out | |
Use a 75 ohm (round) cable.
Power Input
Step 5 : Run Plug & Play
When you turn on your TV for the first time, it automatically launches the Plug & Play function. With Plug & Play, you can select the On Screen Display language, set the clock mode, and launch the TV’s channel memorizing process. It also displays connection instructions similar to those in this guide.
To navigate while Plug & Play is running, press the Up, Down, Left or Right arrow buttons on your remote. To make a selection, press the EnterE button. To skip a screen, press the Menu button.
To turn on your TV, press the Power button on the remote or press the Power button on the TV. To run Plug & Play, follow these steps:
|
| Plug & Play | |||
| Select Language of the OSD. |
|
|
| |
|
|
|
| ||
1 |
|
|
| English |
|
Language |
|
| Español | ||
|
| : English | |||
Français
UMove EEnter
On the Language screen, select the language for the On Screen Display (OSD) using your remote control, and then press EnterE button. The Home Use screen appears.
Plug & Play
Select ‘Home Use’ when installing this TV in your home.
2
Store Demo | Home Use |
LMove EEnter
Select Home Use, and then press EnterE button. If you select Store Demo, the TV will reset your picture and audio settings every 30 minutes. After you press EnterE button , the Antenna Source screen appears.
|
| Plug & Play |
| Select the Antenna source to memorise. | |
3 | Air | Start |
Cable | Start | |
| Auto | Start |
UMove EEnter mSkip
If your TV is only attached to an antenna, select Air. If your TV is only attached to cable and you have no cable box, select Cable. If your TV is attached to an antenna and cable with no box, select Auto. When done, press EnterE button on your remote. The Select Cable System screen appears.
IMPORTANT: If your TV is attached to a cable or satellite box,
skip Steps 3 through 5. After Plug & Play is complete, set your TV to Channel 3 or 4, according to the directions for your cable or satellite box.
|
| Plug & Play |
| |
|
| Selects the cable system. |
| |
4 | Analog | STD | HRC | IRC |
Digital | STD | HRC | IRC | |
Start |
UMove EEnter mSkip
If your TV is attached to a cable system and you have no cable box, you must select your cable system type. If you have Digital cable, you must select the cable system type for both Analog and Digital.
After you have selected the cable system type, select Start, and then press the EnterE button on your remote.
✎✎ Most cable systems are Standard (STD) systems. If you are not sure about what kind of cable system you have, contact your cable company.
|
|
|
| Plug & Play |
|
|
| Auto Program in Progress. |
|
| |||
5 | DTV Cable : | Cable : | Cable 28 | |||
|
|
|
|
| 15% | |
|
|
|
|
| ||
Stop |
EEnter mSkip
The TV memorizes the available channels. This process can take up to 45 minutes.
|
| Plug & Play | |||
| Set the Clock Mode. |
|
|
|
|
6 |
|
|
| ||
|
| Auto |
|
| |
Clock Mode |
| : English |
|
| |
|
| ||||
|
|
| Manual | ||
|
|
|
|
|
|
UMove EEnter mSkip
After the TV has memorized the channels, choose the Clock Mode. Select Auto if you have a digital channel in your area. Select Manual if you don’t, or if you have a cable or satellite box. When done, press EnterE button.
✎✎ If you select Manual, the clock setting screen appears.
|
| Plug & Play | |||
| Set to daylight saving time. |
|
|
| |
|
|
|
| ||
7 |
|
|
| Off |
|
DST |
|
| On |
| |
|
|
| : English |
| |
|
|
|
| Auto | |
|
|
|
|
|
|
UMove EEnter mSkip
Select the daylight savings time setting: Off, On, or Auto, and then press EnterE button.
After the time zone screen, The connection method for best HD screen quality is displayed. Press Right
8 arrow button on your remote to view each screen in succession. Press the Menu button to skip this section.
The Enjoy your TV screen
9 appears. Then press EnterE button.
English - 1