Samsung LE19R7 Installing Batteries in the Remote Control, Switching On and Off, Plug & Play

Page 8

Installing Batteries in the Remote Control

1.Lift the cover at the back of the remote control upward as shown in the figure.

2.Install two AAA size batteries.

Make sure to match the “+” and “–” ends of the batteries with the diagram inside the compartment.

3.Replace the cover.

Remove the batteries and store them in a cool, dry place if you won’t be using the remote control for a long time. The remote control can be used up to about 23 feet from the TV. (Assuming typical TV usage, the batteries last for about one year.)

If the remote control doesn’t work, check the following:

1.Is the TV power on?

2.Are the plus and minus ends of the batteries reversed?

3.Are the batteries drained?

4. Is there a power outage, or is the power cord unplugged?

5. Is there a special fluorescent light or neon sign nearby?

Switching On and Off

The mains lead is attached to the rear of your set.

1.Plug the mains lead into an appropriate socket.

The standby indicator lights up on the front of the set.

2.Press the button on the front of the set.

You also can press the POWER button or the TV () button on the remote control to turn the TV on. The programme that you were watching last is reselected automatically.

3.Press the numeric button (0~9) or channel up/down ( / ) button on the remote control or

button on the right side of the panel.

When you switch the set on for the very first time, you will be asked to choose language in which the menus are to be displayed.

4.To switch your set off, press the POWER button again.

Placing Your Television in Standby Mode

Your set can be placed in standby mode in order to reduce the power consumption. The standby mode can be useful when you wish to interrupt viewing temporarily (during a meal, for example).

1.Press the POWER button on the remote control.

The screen is turned off and a standby indicator appears on the front of your set.

2.To switch your set back on, simply press the POWER , numeric buttons (0~9) or channel up/down ( / ) button again.

Do not leave your set in standby mode for long periods of time (when you are away on holiday, for example). It is best to unplug the set from the mains and aerial.

Plug & Play

When the TV is initially powered on, several basic settings proceed automatically and subsequently. The following settings are available.

1.Press the POWER button on the remote control.

The message “Start Plug & Play” is displayed with “OK” selected. Press the ENTER button.

2. Select the appropriate language by pressing the

or

button.

Press the ENTER button to confirm your choice.

 

 

3.The message “Check antenna input.” is displayed with “OK” selected. Press the ENTER button.

Please check that the antenna or cable TV is connected correctly. English-6

Page 7 Page 9
Image 8
Page 7 Page 9
Contents 02 201 844 00038 322 09 693 79Precautions When Displaying a Still Image Contents Registration Card Decoration Cover List of FeaturesPower Cord Wall Mount kit Speaker Power Power IndicatorRemote Control Sensor Viewing the Control PanelConnecting DVI Viewing the Connection PanelViewing the Remote Control Teletext FunctionsInstalling Batteries in the Remote Control Switching On and OffPlacing Your Television in Standby Mode Plug & PlayStoring Channels Automatically Select the appropriate country by pressingSet the Hour or Minute by pressing Button PressStoring Channels Manually Editing the Channels Sorting the Stored ChannelsPress the Exit button to exit Press the Enter buttonFine Tuning Channel Reception Assigning Channels NamesChanging the Picture Standard Adjusting the Custom PicturePC mode Changing the Colour Tone Changing the Picture SizeTo select Picture, then press the Enter button Press the or button to select Size, then pressAdjusting the Colour Control Freezing the PicturePress Button to select Picture, then press Enter button Press the Still button to freeze a moving pictureSelecting the Sound mode Changing the Sound StandardCustomizing the Sound To select Sound, then press the Enter buttonPress Adjusting the Volume AutomaticallySetting and Displaying the Current Time Setting the Sleep Timer Switching the Television On and Off Automatically Press Button to select On Timer, then press Enter buttonChoosing Your Language Button toSetting the Blue Screen Mode Selecting the SourceTeletext Decoder Part ContentsEditing the Input Source Names Displaying the Teletext Information Selecting a Specific TeletextPress the TTX/MIX button again Press the TV button again to exit from the Text displayStoring Teletext Pages Using Fastext to Select a TeletextSelect the List mode using the Source button First, click on Control Panel on the Windows start menu Setting up Your PC Software Based on Windows XPDisplay Modes Setting the PC Press the Enter button to select Image LockPress the Enter button Press the Exit button to exit Enter button Press the Exit button to exitHow to Adjust the Stand How to Adjust the Angle of the TVInstalling the Wall Mount Kit Installing Vesa compliant mounting devicesTroubleshooting Before Contacting Service Personnel Technical and Environmental SpecificationsRisk of Electric Shock do not Open Wiring the Mains Power Supply Plug UK Only Warranty Card
Top Page Image Contents