Samsung PS50A550 user manual Check Points before Requesting Service

Listening through a Receiver
You can listen to sound through a receiver instead of the TV speaker.
		TV	P 1
1	Press the MENU button to display the menu. Press the ▲ or ▼ button to
			View TV
2	select Input, then press the ENTER button.		Select Device		
	Press the ▲ or ▼ button to select Anynet+ (HDMI-CEC), then press the		Record		
	ENTER button.		Menu on Device		
3	Press the ▲ or ▼ button to select Receiver, then press the ENTER button.		Device Operation		
	Press the ◄ or ► button to select to On, then press the ENTER button.		Receiver	:On	
	Now you can listen to sound through the receiver.		Setup		
4	Press the EXIT button to exit.		Move	Enter
➢ When the receiver is set to On, you can listen to the TV sound through the			Return
	2-channel receiver.

➢If the receiver is exclusively for a home theater only (supporting audio only), it may not appear in the device list.

➢In case of a content with copyright problem, listening through the receiver may not properly operate.

➢When executing WISELINK, the listening through the receiver may not work properly.

➢When listening through the receiver, there are restrictions for using the PIP and audio-related menu.

Check Points before Requesting Service

Symptom	Solution
Anynet+ does not work.	■ Check if the device is an Anynet+ device. The Anynet+ system
		supports Anynet+ devices only.
	■ Connect only one receiver.
	■ Check if the Anynet+ device power cord is properly connected.
	■	Check the Anynet+ device’s Video/Audio/HDMI 1.3 Cable connections.
	■ Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+
		setup menu.
	■ Check whether the TV remote control is in TV mode.
	■ Check whether it is Anynet+ exclusive remote control.
	■ Anynet+ doesn’t work at a certain condition. (Searching channels,
		Operating WISELINK)
I want to start Anynet+.	■ Check if the Anynet+ device is properly connected to the TV and
		check if the Anynet+ (HDMI-CEC) is set to On in the Anynet+ Setup
		menu.
	■ Press the TV button on the TV remote control to switch to TV. Then
		press the TOOLS button to show the Anynet+ menu and select a
		menu you want.
I want to exit Anynet+.	■ Select View TV in Anynet+ menu.
	■ Press the SOURCE button on the TV remote control and select a
		device other than Anynet+ devices.
	■ Press any of P, CH LIST, PRE-CH, and such to change to the
		TV mode. (Note that the channel button operates only when a
		tuner-embedded Anynet+ device is not connected.)
The Connecting to Anynet+	■ You cannot use the remote control when you are configuring
device… message appears		Anynet+ or switching to a view mode.
on the screen.	■ Use the remote control when the Anynet+ setting or switching to
		view mode is complete.
The Anynet+ device does	You cannot use the play function when an auto channel scan is in
not play.	progress. Stop the currently running function.
The connected device is not	■ Check whether or not the device supports Anynet+ functions.
displayed.	■ Check whether or not the HDMI 1.3 Cable is properly connected.
	■ Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+
		setup menu.
	■ Search Anynet+ devices again.
	■ You can connect an Anynet+ device using the HDMI 1.3 Cable
		only. Some HDMI cables may not support Anynet+ functions.
The TV program cannot be	Check whether the antenna jack on the recording device is properly
recorded.	connected.

English - 43