Toshiba 52HM95, 62HM95 Labeling the video input sources, DTV Satellite/DSS Cable Game Console

Chapter 8: Using the TV’s features

Labeling the video input sources

You can label each video input source according to the type of device you connected to each source, from the following preset list of labels:

–– (default label)

Hide (to hide an unused input in the Input Selection window)

Audio Receiver

VCR

Video Recorder Laser Disk Compact Disc

DVD

DTV Satellite/DSS Cable Game Console

Note:

•	If you set up devices in TheaterNet,™ the associated inputs are
	automatically labeled and cannot be relabeled until you remove the
	device from TheaterNet (see page 45).
•	If you set up a cable box in VIDEO 1, that input will be labeled
	automatically and cannot be relabeled until you remove the device

4.Press x or • to select the desired label for that input source. If a particular input is not used, you can select “Hide” as the label, which will cause that input to be “grayed out” in the input list and skipped over when you press the INPUT button on the remote control.

Note: If you select “Hide” for all of the input labels, the POP feature will be disabled. If you then attempt to access the POP feature, the message “Not available” will appear on-screen.

5.To save the new input labels, highlight Done and press ENTER. To revert to the factory default labels, highlight Reset and press ENTER.

Input labeling example:

The screen below left shows the default Input Selection screen (with none of the inputs labeled). The screen below right is an example of how you could label the inputs if you had connected a DVD player to VIDEO 1, Cable TV to VIDEO 2, an audio receiver to VIDEO 3, a video recorder to ColorStream HD1, a DTV set-top box to HDMI 1, and a satellite/DSS set-top box to HDMI 2. Also note that the ColorStream HD2 input is labeled “Hidden,” which means that the input will be skipped over when INPUT or TV/VIDEO is pressed.

from the TV Guide On Screen® setup.

• You cannot select IEEE1394 devices through the Input Selection

window; however, you can select and control IEEE1394 devices

through TheaterNet (see page 45).

To label the video input sources:

1.Press MENU and open the Preferences menu.

2.Highlight Input Labeling and press ENTER.

3.Press y or z to highlight the video source you want to label.

Input Selection ANT 1

0 ANT 1

1Video 1

2Video 2

3Video 3

4ColorStream HD1

5ColorStream HD2

6HDMI 1

7HDMI 2

8ANT 2

0 - 8 / INPUT to Select

Input Selection screen with no inputs labeled

Input Selection ANT 1

0 ANT 1

1DVD

2Cable

3Audio Receiver

4Video Recorder

5ColorStream HD2 (Hidden)

6DTV

7Satellite/DSS

8ANT 2

0 - 8 / INPUT to Select

Input Selection screen with

all inputs labeled except input 5, which has been hidden.

Preferences

	Favorite Channels
	Closed Caption Mode			Off
	Closed Caption Advanced
	Input Labeling
	Menu Language			English
	Home CH Setup
	Navigate		Select CH RTN Back EXIT Exit
Input Labeling
Video 1						DVD
Video 2						Cable
Video 3					Audio Receiver
ColorStream HD 1					Video Receiver
ColorStream HD 2						Hide
HDMI 1						DTV
HDMI 2					Satellite/DSS
ANT 2				- -
		Reset			Done

To clear the input labels:

1.Press MENU and open the Preferences menu.

2.Highlight Input Labeling and press ENTER.

3.Highlight Reset and press ENTER.

4.Highlight Done and press ENTER.

Note: If you set up a device in TheaterNet, its input label will not be cleared unless you remove the device from TheaterNet (see page 45).

68		Copyright © 2005 TOSHIBA CORPORATION. All rights reserved.
HM95_R2_067-78_061505	68	6/27/05, 4:32 PM

(E) 46/52/62HM95