Dometic REMOTE COMFORT CONTROL manual System Override, Feel Operation, Remote Reset

SYSTEM OVERRIDE

1. This is useful in the event the remote batteries are low or the remote is misplaced.

2. System Override - Cooling Operation

a. Push the “Cool” button on the receiver.

b. System goes to the cooling mode with a set point of 74 °F. and the Green LED will

REMOTE CONTROL

(w/door open) Operation Mode Display Window

blink.

3. System Override - Heating Operation (if connected to furnace)

a. Push the “Heat” button on the receiver.

b. System goes to the “heat” mode with a set point of 68 oF.

•First option: Electric heat-the control system will automatically choose this op- tion, the Green Led will glow steady.

•Second Option: Furnace-The furnace option is chosen if an electric heat strip is not available. When in this option the Red LED will blink and the Green LED will glow steady.

	RECEIVER
Green LED	Unit On
Orange LED	Cool
	Timer
Red LED	Heat

Timer ON/OFF

Display	10:00	10:00
	ON	OFF
Clock Display	10:00
	75°F I FEEL
UP (+)
	AUTO
Down (-)
Clock	+
	-	MODE
F°/C° Button
		CLOCK
Timer	F°/C°
		TIMER
Set		SLEEP
Room		SET
	ROOM	I FEEL

Reset Button

Low Battery

Room Temperature

I Feel Display

Sleep Display

Orange

ON/OFF Button

Sleep

I Feel

Furnace

Note: LED’s will glow and flash even if the system is cooling only.

4. The system can be turned “OFF” by pushing the same button (cool/heat) a second time.

“I FEEL” OPERATION

1.The cool, heat, furnace or auto change mode must be selected.

2.Set the temperature at the desired level, and push the “I Feel” button. The “I FEEL” symbol will appear on the display and a beep will sound indicating that the unit is in “I FEEL” mode.

IFEEL

3.The hand held remote becomes the temperature sensor and must be positioned to send updated signals to the receiver every four minutes.

4.The temperature can be adjusted to the desired level from the remote for its specific location.

Note: If the remote is placed in a location where the receiver cannot locate a signal for 16 minutes, the system will ignore the hand held remote and retain the last set-point.

Note: The remote should not be placed in an area that is warmer or colder than the rest of the living space (direct sunlight or air conditioner discharge drafts).

FAHRENHEIT/CELSIUS TEMPERATURE DISPLAY

1.Locate the F°/C° Button under the door of the hand held remote. Push the button to display Fahrenheit (F°) temperature reading or press again to display Celsius (C°)

REMOTE RESET

1.The “Reset Button” is located on the hand held remote under the door below the “Set Button”. Depress this button to delete all setting programmed into the control.

TIMER OPERATION

Note: Every time the clock or timer button is pressed, the display will blink for 15 seconds giving the operator enough time to change settings. If no changes are made in the 15 second time period the timer display will disappear.

Note: Any mode that uses the clock/timer function of the hand held remote will be disabled if the line of sight communication between the remote and receiver are non existent (putting the remote in a drawer).

2.Setting The Timer to “ON”

a.Press the “timer” button and the timer “ON” clock will appear and blink.

b.Set timer by pushing and holding the “UP(+)” or “DOWN (-)”buttons.

c.Point hand held remote at the receiver and press the “SET” button.

d.Receiver should beep and the Orange LED illuminate (if unit is off).

Note: When timer “ON” mode is activated the unit will turn “ON” in the last selected mode of operation. See TIMER OPERATION.

3.Setting The Timer to “OFF”

a.Press the “timer” button twice and the timer “OFF” clock will appear and blink.

b.Set timer by pushing and holding the “UP(+)” or “DOWN (-)”buttons.

c.Point hand held remote at the receiver and press the “SET” button.

d.Receiver should beep and the Orange LED illuminate (if unit is on).

Note: When timer “Off” mode is activated the unit will turn “OFF” when the clock & timer match. See TIMER OPERATION.

4.Setting The Timer to “ON” &“OFF”

a.Press the “timer” button three times and the timer “ON” clock will blink and “OFF” clock will be visible.

b.Set “ON” timer by pushing and holding the “UP” or “DOWN” buttons, then push the timer button again and the “OFF” will blink. Press and hold “UP (+)” or “DOWN (-)”to set “OFF” time.

08:00 20:00

ON OFF

c. Point hand held remote at the receiver and press the “SET” button. d. Receiver should beep and the Orange LED illuminate (if unit is on).

Note: The Orange LED will light indicating the timer schedule is active. The unit will cycle on and off in the last mode selected. See TIMER OPERATION.

CONFIGURATION OF REMOTE

The Hand Held Remote when shipped from Dometic is always programmed as a cool/ furnace model. The dip switches are located in the hand held remote battery compartment. If the control is to be used with the electric heat strip or without the furnace its configuration must be changed as follows:

1.Cool/furnace operation: Dip switches 1,2,& 3 "ON" - dip switch 4 "OFF".

2.Cool Only-no heat operation: Dip switch 1 & 3 "ON" - dip switches 2 & 4 "OFF".

3.Cool/Heat operation: Dip switches 1,2,3, & 4 "ON" -no dip switches "OFF".

Note: After the remote switches are changed press the reset button and reenter clock and timer settings.

BATTERY COMPARTMENT

REMOTE

COMFORT CONTROL

75	10:00
	°F
AUTO

+ -

MODE

USER’S GUIDE

1. Setting The Clock

J1 J2 J3 J4

Dip Switches "OFF"

	a. When new batteries are installed, the clock will display 0:00.
B	b. Clock shows only military time.
LBO231-REV
	c. Push the clock button , the clock display should blink.
	d. Press and hold the “UP(+)” or “DOWN (-)”button to set the clock.

e. Press the “SET” button on hand held remote.

Note: When the set button is depressed be careful not to push the reset button at the same time. All previous setting will be lost and need to be reentered.

Dip Switches	OFF
"ON"	REVISION
	Form No. 3308571.029 12/04
	(Replaces 3308571.011
	(French 3308572.027)
	©2004 Dometic Corporation
	LaGrange, IN 46761