Dynalink A 1012 manual Set up by Automatic Search, Setting up by Manual Search

Page 3

A 1012 Dynalink Learning Universal Remote Control

remains in set-up mode. If this occurs you should enter the correct code from the list again within 10 seconds.

5.Once programmed,. check the function of the keys on A 1012 remote control. If most keys on your new remote control do not function correctly, try another 3- digit device code (e.g. 004…) from the list under the same brand. Repeat steps 3 to 6 until all the basic functions operate correctly.

6.To leave set up mode, press the device key (e.g. TV). If you do not actuate any keys within 10 seconds it will automatically exit set up mode.

B.Set up by Automatic Search:

If setting up by brand name and codes is unsuccessful, or you can not find your brand name in the list, you can use the “Automatic Search” to find the correct code for your remote control.

1.Switch on the power for the device that you want to control.

2.Point the A 1012 remote control at your device. Press the SET and the device (e.g. TV) keys simultaneously and hold them down for 3 seconds. The device key will flash, showing the remote control is now in Automatic Search mode.

3.When the correct device has been found, the remote control will send an OFF signal to the device from the remote control (code scan). When the device (e.g. TV) switches off, immediately press any key (except SET key) to stop the Automatic Search.

4.Switch the device on again by pressing the “POWER” key to check the operation. Check the functions of other keys on the remote control. If most or all of the keys do not function correctly, repeat the automatic search again ensuring you press any key immediately when your device turns off. If most key’s function properly then the set up is successful. Press the device key (e.g. TV) again to save the code and finish the set up.

Note 1 .To abort the “Automatic Search”, press any key (except set key). The LED lamp will go out and the search is terminated.

Note 2. The “Automatic Search” will be terminated automatically after it goes through all codes, and the LED will extinguish.

C. Setting up by Manual Search:

If setting up with brand name and codes is unsuccessful, you can also use the “Manual Search” to find the correct code for operating your device.

1.Switch on the device that you want to control.

2.Point the A 1012 remote control at your device. Press and hold the SET key and press the device key (e.g. TV) in a short time (less than 3 seconds, to prevent the unit going to Automatic Search), then release both pressed keys.

3.The device key will light up continuously and the remote control is now in set-up mode.

4.To search for your device press the POWER (ON/OFF) key about every 1.5 seconds.The POWER button will now flash, showing that the remote control is in Manual Search mode. When your device has been found the device will switch off. Alternatively, if the device being sought is a video recorder, DVD player, CD player, AUX etc., you can also press the PLAY instead of POWER and search for PLAY activation. Once the searched device starts PLAYing the A 1012 is programmed. Test the functions of other keys (don’t press POWER button or PLAY button, as the remote will go to next code) on the remote control. If most of the buttons do not function properly, continue to press the POWER key about every 1.5 seconds again to search for the next activated code that turns the POWER OFF or starts PLAYing. If most of the keys on the remote control work

well, you can save the code by pressing the device key (e.g. TV) to finish the Manual Search.

Note 1. The Manual Search will be automatically terminated if no entry is made within 30 seconds.

Note 2. The “Manual Search” will be terminated automatically after it goes through all codes and LED will light off. But you can start it again if necessary.

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Dynalink 6 In 1 Universal Remote Control Operating Instructions Set up by Brand Code Battery InstallationSetting up by Manual Search Set up by Automatic SearchOther Functions Display the Device Code Set up by LearningWrite-protection of Device Codes Reset / Delete FunctionVolume lock Device ShiftDevice Brand Code List Dynalink Learning Universal Remote Control DTS CTCGCM ELGESC GBCICE GPMGTT HCMITS ITCITE ITLNAD MTCPCM NECNEI OSOREX PRO2RBM RCASBR SEGSEI TEC STMTCL TCMDynalink Learning Universal Remote Control VCR 002,003,101,102 Funai 002,101 Galaxi Galaxy National 029,031,126,167 094 TVA TMKAST SATCBL/SAT AGSDNT CNTDDC DEWFTE GMIHedy 003,075,236 OAK 010,103,125,242,244 TPS BSR SAE BBK DVDDVD DVR AMWJBL ECGGVG HTYSVA RTLDBS AMP Tuner Tape LD/OTHER ADTASH CDR068,118 TCM

A 1012 specifications

The Dynalink A 1012 is a versatile and compact device that has rapidly gained popularity among tech enthusiasts and professionals alike. Known for its impressive capabilities in data management and connectivity, the A 1012 is tailored for various applications, from home networking to office environments.

One of the standout features of the Dynalink A 1012 is its dual-band wireless capability. Operating on both the 2.4 GHz and 5 GHz bands, this device ensures users can experience seamless connectivity regardless of their internet needs. The 2.4 GHz band offers extended coverage, making it ideal for connecting various devices across a larger area, while the 5 GHz band provides faster speeds, perfect for high-bandwidth activities such as online gaming and video streaming.

The A 1012 is also equipped with advanced security technologies that help protect user data and privacy. With WPA3 encryption, it provides enhanced security protocols, safeguarding the network from unauthorized access and cyber threats. This level of security is essential in today's digital age, where data breaches are increasingly common.

Moreover, the Dynalink A 1012 features multiple Ethernet ports, enabling owners to connect wired devices directly. This is particularly beneficial for gaming consoles, smart TVs, or any other device that requires a stable internet connection. The simultaneous support for both wired and wireless devices caters to a broad spectrum of users.

A key characteristic of the A 1012 is its user-friendly interface. Setting up the device is a straightforward process, with a step-by-step guide that allows even those with minimal technical knowledge to establish a secure network. Additionally, the device supports remote management, which means users can monitor their network's performance and make adjustments from anywhere.

Furthermore, the Dynalink A 1012 supports various QoS (Quality of Service) features. This technology prioritizes bandwidth allocation, ensuring that critical applications, such as video conferencing or online gaming, receive adequate resources even when the network is under heavy load.

In conclusion, the Dynalink A 1012 is an impressive device that combines robust performance with user-friendly features. With its dual-band support, advanced security measures, and easy setup, it meets the diverse connectivity needs of modern users. Whether for home or office use, the A 1012 stands out as a reliable choice for enhancing network performance and security.
Top Page Image Contents