CLO Systems UR5-8400A manual Introduction, Replacing Batteries

Page 1

Operating Instructions

For The UR5-8400A

Cable Remote Control

UR5-8400A

Universal Remote Control, Inc.

www.universalremote.com

OCE-0019B Rev 03 (11/29/05)

1Introduction

The remote control is designed to operate the Scientific Atlanta Explorer 8000, Pioneer Voyager DVR and the Pace Micro DVR Series. You can also control the majority of TV, VCR, DVD and AUDIO equipment on the market as shown below.

CABLE

: Cable Converters

TV : Televisions

VCR

: VCRs and TV/VCRs

DVD : DVD Players

AUX

: Audio Receivers, SAT, DVR, etc.

2Replacing Batteries

Before you program or operate the remote control, you must install two new AA alkaline batteries.

STEP1 Remove the battery compartment cover on the back of your remote control.

STEP2 Check battery polarity carefully, and install the batteries as shown In the illustration below.

STEP3 Replace the battery compartment cover.

4 Operations

Default State:

Device Default: CABLE

Volume Default: You have the option of controlling your TV volume and mute through the Cable box, VCR or DVD. Refer to section G for programming the volume and mute through your Cable box, VCR or DVD.

Channel Default: You have the option of controlling your CABLE channel and number keys through the TV or VCR. Refer to section F for programming the channel and number keys through your TV or VCR.

System On/Off button:

This button is designed to send out power commands for two, three, four or all five devices with one button press. Please refer to section E for details.

3 Button Functions

5Programming the Remote Control

A.Three-Digit Code Programming Method.

The remote control can be programmed by pressing in a three-digit code number that corresponds to particular manufacturers and brands of Audio/Video equipment. The three-digit code numbers are listed in the code table of the instruction manual.

STEP1 Turn on the equipment you wish to program. (TV, VCR, DVD or AUX)

STEP2 Press the [DEVICE] button (TV, VCR, DVD or AUX) to be programmed and [SELECT] button simultaneously for 3 seconds. The device LED will turn on indicating the unit is ready to be programmed.

*Tip : The device LED will turn on for 20 seconds. The next step must be entered while the LED is on.

STEP3 Point the remote control toward the equipment and enter the three-digit code number assigned to your brand from the code tables.

*Tip : The equipment will turn off when the correct three-digit code number has been entered. You can verify you have selected the correct code by pressing the [POWER] button, the equipment should turn on or turn off.

*Note : If there is more than one three-digit number listed for your brand, try one code number at a time until your equipment turns off.

STEP4 Store the three-digit code number by pressing the same [DEVICE] button once again. The device LED will blink twice to confirm that the code has been stored.

*Note : Try all the functions on the remote control. If any of the functions do not work as they should, repeat from Step 2 using the next three-digit code number from the same brand list.

B. Auto Search Method.

If the three-digit code numbers assigned to your brand do not turn off your equipment or the code tables do not list your brand, you can use the Auto Search Method to find the correct three-digit code number for your equipment by the following steps:

STEP1 Turn on the equipment you wish to operate.

STEP2 Press the [DEVICE] button (TV, VCR, DVD or AUX) to be programmed and the [SELECT] button simultaneously for 3 seconds. The device LED will turn on.

*Tip : The device LED will turn on for 20 seconds. The next step must be entered while LED is on.

STEP3 Press the [CH+] or [CH-] button one at a time or keep it pressed. The remote will emit a series of power on/off commands. Release the [CH+] or [CH-] button as soon as the equipment turns off.

*Tip : You can verify that you selected the correct code by pressing the [POWER] button. The equipment should either turn on or turn off.

STEP4 Press the same [DEVICE] button to store the code. The device LED will blink twice to confirm that the code has been stored.

C. To Find the Three Digit Code Number That was Stored in the Device.

STEP1 Press the [DEVICE] button (TV, VCR , DVD or AUX) you wish to verify and the [SELECT] button simultaneously for 3 seconds. The device LED will turn on.

*Tip : The device LED will turn on for 20 seconds. The next step must be entered while the LED is on.

STEP2 Press the [INFO] button.

The device LED will blink number of times indicating the number of each digit of the code number. Each digit is separated by a 1 second interval of the LED being turned off.

Example : One blink, three blinks and eight blinks with an interval of 1 second of LED being turned off, indicates the code number 138.

Note : Ten blinks is equal to the number 0.

D. Programming a second TV to AUX Mode.

STEP1 Press the [AUX] button to be programmed and the [SELECT] button simultaneously for 3 seconds.The [AUX] device LED will turn on.

*Tip : The device LED will turn on for 20 seconds. The next step must be entered while the LED is on.

STEP2 Press the [TV] device button to pick up the TV code table.

STEP3 Point the remote control toward the equipment and enter the three-digit code number assigned to your TV brand from the code tables.

STEP4 Store the three-digit code number by pressing the [AUX] button once again. The device LED will blink twice to confirm that the code has been stored.

E. Programming the System On/Off Button.

This is designed to program the System On/Off button so that it can send out up to five power on/off commands with one button press.

STEP1 Press the [CBL] button.

STEP2 Press the [SYSTEM ON/OFF] button and the [SELECT] button simultaneously for 3 seconds. The [CBL] button will turn on for 20 seconds.

STEP3 Press the [DEVICE] button and the [POWER] button you wish to store in the [SYSTEM ON/OFF] button and repeat this until you stored all the power commands into the [SYSTEM ON/OFF] button.

STEP4 Press the [CH+] button to save the power commands you stored. The [CBL] button will blink twice to confirm the saving.

F. Programming Channel Control.

By following the steps below, the user can program the channel controls (Channel Up, Channel Down and Last) from one device to operate in another device mode. The default channel control settings on the remote control are as follows:

CBL : CBL

T V : CBL

VCR : CBL

DVD : DVD

AUX : AUX

 

If you wish to store the TV channel control in TV mode, use the following steps.

STEP1 Press the [TV] button and the [SELECT] button simultaneously for 3 seconds.

The [TV] device LED will turn on.

*Tip : The device LED will light on for 20 seconds. The next step must be entered while the LED is on.

STEP2 Press the [VOL -] button.

STEP3 Press the [TV] button.

The device LED will blink twice to confirm the programming.

To return to original state:

If you wish to restore the CABLE channel control in TV mode, repeat the above steps

by pressing [CBL] in STEP3 .

G. Programming Volume Control.

By following the steps below, the user can program the volume controls (Volume Up, Volume Down and Mute) from one device to operate in another device mode. The default volume control settings on the remote control are as follows:

CBL : TV

T V : TV

VCR : TV

DVD : TV

AUX : AUX

 

If you wish to store the CBL volume control in CBL mode, use the following steps.

STEP1 Press the [CBL] button and the [SELECT] button simultaneously for 3 seconds.

The [CBL] device LED will turn on.

*Tip : The device LED will turn on for 20 seconds. The next step must be entered while the LED is on.

STEP2 Press the [VOL +] button.

STEP3 Press the [CBL] button.

The device LED will blink twice to confirm the programming.

To return to original state:

If you wish to restore the TV volume control in CBL mode, repeat the above steps by pressing [TV] in STEP3 .

H. Programming For Advanced Function.

In the CBL mode, the BLANK button can be programmed to act as a macro or favorite channel button. You can send out up to ten commands with one button press.

STEP1 Press the [CBL] button to select the CBL mode.

STEP2 Press the BLANK button and [SELECT] button simultaneously for 3 seconds. The [CBL] device LED will turn on for 20 seconds.

STEP3 Press up to 10 buttons you wish to store. The [CBL] device LED will blink once for each command entered.

STEP4 Press the [CH+] button to store the functions that were selected. The [CBL] device LED will blink twice to confirm the storage of functions.

I. Low Battery Warning.

When the batteries are low and need to be replaced with fresh batteries, the remote control LED will blink 2 times in sequence whenever a [POWER] button is pressed to turn on equipment.

J. Memory Lock System.

This remote control is designed to retain programmed memory for 10 years even after batteries are removed from the remote control.

K.Write your device Set-up codes.

TV

Set-up Code Number:

VCR

Set-up Code Number:

DVD

Set-up Code Number:

AUX

Set-up Code Number:

Page 1 Page 2
Image 1
Page 1 Page 2
Contents Introduction Button Functions Programming the Remote ControlReplacing Batteries Cable TV Set-up Code TablesDVD & TV/DVD DMX & Dcraux

UR5-8400A specifications

The CLO Systems UR5-8400A is an advanced robotic arm designed for a wide array of industrial applications, combining cutting-edge technology and robust features to enhance productivity and efficiency in manufacturing processes. This flexible robot is particularly well-suited for tasks such as assembly, welding, packaging, and material handling, making it an invaluable asset in modern production environments.

One of the primary features of the UR5-8400A is its adaptability. With a payload capacity of up to 5 kilograms, the arm can handle various tools and components, allowing for seamless integration into existing workflows. Its ability to operate in diverse environments, including small workshops and large production lines, showcases its versatility.

The UR5-8400A is equipped with advanced motion control technology, providing smooth and precise movement. It offers a reach of 850 millimeters, enabling it to cover large areas and operate within confined spaces without compromising functionality. This capability is particularly useful in tasks that require intricate movements or repetitive actions, reducing the risk of errors and enhancing overall efficiency.

Another significant aspect of the UR5-8400A is its ease of programming. The robot features an intuitive user interface that allows operators, even those with minimal coding experience, to set up and run applications quickly. The collaborative nature of the robot enables it to work alongside human workers without the need for safety barriers, promoting a cooperative environment where robots and people can enhance productivity together.

The UR5-8400A is also designed with safety in mind. Integrated sensors and a lightweight build allow it to detect human presence, enabling it to slow down or stop when someone enters its workspace. This cutting-edge safety feature ensures that the robot can operate close to human workers, making it an ideal choice for modern collaborative manufacturing settings.

In terms of connectivity, the UR5-8400A supports various communication protocols, allowing it to integrate seamlessly with other industrial devices and systems. This connectivity facilitates real-time data gathering, monitoring, and adjustments, ensuring optimal performance and reduced downtime.

Overall, the CLO Systems UR5-8400A represents a significant advancement in robotic automation, combining flexibility, ease of use, and safety features. With its robust capabilities and user-friendly design, it stands out as a reliable solution for businesses looking to optimize their manufacturing processes and stay competitive in an ever-evolving market.
Top Page Image Contents