Installation | Soundstream Technologies 805, 405 specs

INSTALLATION STEP 3

INSTALLATION AND MOUNTING

AMPLIFIER LOCA T/ON

The RUBICON amplifier employs highly efficient circuitry, a custom-engineered heat sink, and a unique Chassisink construction to maintain lower operating tem- peratures. Additional cooling may be required if the amplifier is located in a tightly confied area or when driving especially low impedance loads at extremely high levels.

When mounting the amplifier, it should be securely mounted to either a panel in the vehicle or an amp board or rack that is securely mounted to the vehicle. The mounting location should be either in the passenger compartment or in the trunk of the vehicle, away from moisture, stray or moving objects, and major electrical com- ponents. To provide adequate ventilation, mount the amplifier so that there are at least two inches of freely circulating air above and to the sides of it.

MOUNTING THE AMPLIFIER

a.Using the amplifier as a template, mark the holes on the mounting surface.

b.Remove the amplifier and drill the holes for the mounting screws.

C.Secure the amplifier to the mounting surface using the supplied hardware.

WIRING

a.Run and connect the audio signal and remote turn-on cables to the amplifier from the source unit.

b.Carefully Nn the positive cable from the amplifier to a fuse or circuit breaker

within 18” of the battery.

C.Connect the fuse or circuit breaker lead to the battery. Leave the circuit breaker off or the fuse out until everything is bolted down.

d.Secure the ground cable to a solid chassis ground on the vehicle. It may be necessary to sand paint down to raw metal for a good connection.

e.Double check each and every connection!

f.Re-connect the fuse or circuit breaker.

POWER UP

Power up the system and look at the Power LED; there may be a 2-3 second delay from the time the source unit is turned on to the time that the LED on the amp turns on, which is normal. Once the amplifer LED is on and the source unit is playing, you should have sound coming from the speakers.

( INSTALLATION STEP 4 1

LEVEL SETTING

The input levels are adjusted by means of the input level controls located on the front of the amplifier. This is a unique dual-stage circuit that adjusts both level and gain. This topology maintains better S/N Ratio even when using sources with minimal output.

In the ideal situation, all components in the audio system reach maximum undistorted output at the same time. If you send a distorted signal to an amplifier, it is simply going to amplify distorted information. The same holds true if an outboard proces- sor or crossover begins to distort before you have maximum output from the ampli- fier. By setting all components to reach clipping at the same time, you can maxi- mize the output of your system. For the RUBICON amplifier, follow these steps for setting the input levels:

1.Turn the amplifier’s input levels to minimum position (counter-clockwise)

2.Set the source unit volume to approximately 3/4 of full volume.

3.While playing dynamic source material, slowly increase the amplifiers’ input level until a near maximum undistorted level is heard in the system.

Once the amplifier is installed and the proper levels set, place the front spoiler in position, and secure it using the supplied hardware.

405, 805 specifications

Soundstream Technologies 405,805 is an advanced audio processing unit designed specifically for transforming sound experiences across various platforms. This revolutionary technology incorporates state-of-the-art features that deliver unmatched audio quality, making it an ideal choice for both professionals and audiophiles.

One of the key features of the Soundstream Technologies 405,805 is its high-resolution audio processing capability. It supports an extensive range of audio formats, including PCM, DSD, and MQA, ensuring that users can enjoy their favorite tracks in the highest fidelity possible. The unit boasts a dynamic range of 120 dB, allowing for a crystal-clear sound experience that reproduces even the most subtle nuances in the audio spectrum.

Another notable characteristic of the 405,805 is its advanced digital signal processing (DSP) unit. The built-in DSP allows for customizable sound profiles, enabling users to tailor their listening experience to their preferences. With features such as equalization, spatialization, and room correction, the DSP ensures that the audio performance is optimized for any environment, whether it be a home studio or a live concert setting.

Connectivity is another area where the Soundstream Technologies 405,805 excels. It features multiple input and output options, including USB, HDMI, optical, and coaxial, making it compatible with a wide range of devices. Additionally, its Bluetooth capabilities allow for seamless wireless audio streaming, enhancing convenience for users who prefer mobile connectivity.

The unit is also equipped with a user-friendly interface that simplifies the control of its multitude of features. A large touchscreen display provides intuitive navigation, while customizable presets allow users to switch between audio settings with ease. Furthermore, it supports integration with smart home systems, enabling users to incorporate it into their existing setups effortlessly.

Durability and design are equally important aspects of the Soundstream Technologies 405,805. Constructed with high-quality materials, the unit is both sturdy and stylish, making it an attractive addition to any audio setup. Its compact size ensures it can fit easily into various spaces without compromising on performance.

In summary, Soundstream Technologies 405,805 represents the forefront of audio technology, combining premium sound quality with versatile features, seamless connectivity, and user-friendly design. It is poised to elevate the listening experience for users, whether at home or on the go.