CONNECTING EXTERNAL AUDIO DEVICES
To control the audio level of an external audio amplifier with the remote control, connect the system as shown below.
REAR PANEL OF TELEVISION
FIRST TIME USE
ANT A
TO
CONVERTER
ANT B
AUDIO
TO
CENTER
IN
IR
BLASTER
L
R
|
|
|
| |
| PR | PB | Y |
|
INPUT 1 |
|
|
|
|
| R | (MONO)/L |
|
|
|
|
| AUDIO |
|
| PR | PB | Y/VIDEO | |
INPUT 2 | R | (MONO)/L |
|
|
|
|
| ||
|
|
| AUDIO |
|
| R | (MONO)/L | VIDEO | |
INPUT 3 |
|
|
|
|
| R | (MONO)/L | VIDEO | |
INPUT 4 |
|
|
|
|
| R | L | VIDEO | |
MONITOR |
|
|
|
|
OUT |
|
|
|
|
AUDIO 
ANT A |
|
|
|
|
|
|
| PR | PB | Y | |
| INPUT 1 |
|
|
|
|
TO |
| R | (MONO)/L |
|
|
CONVERTER |
|
|
| AUDIO |
|
|
|
|
|
| |
|
| PR | PB | Y/VIDEO |
|
ANT B | INPUT 2 | R | (MONO)/L |
|
|
|
|
|
| ||
|
|
|
| AUDIO |
|
|
| R | (MONO)/L | VIDEO | |
| INPUT 3 |
|
|
|
|
AUDIO |
|
|
|
|
|
TO |
|
|
|
|
|
CENTER |
| R | (MONO)/L | VIDEO | |
INPUT 4 |
|
|
|
| |
IN |
|
|
|
| |
|
|
|
|
| |
IR |
|
|
|
|
|
BLASTER |
| R | L | VIDEO | |
L | MONITOR |
|
|
|
|
OUT |
|
|
|
| |
|
|
|
|
| |
|
|
| AUDIO |
|
|
R |
|
|
|
|
|
Models: 57T500 65T500
Models: 57X500 |
65X500 |
LR
INPUT
LR
INPUT
Stereo System Amplifier | Stereo System Amplifier |
NOTE: 1. To prevent damage to the speaker and distorted sound, set the volume control of the audio amplifier lower and adjust the sound using the remote control of the TV set.
2. See page 51 for AUDIO Settings.
CONNECTING EXTERNAL VIDEO SOURCES
The exact arrangement you use to connect the VCR, camcorder, laserdisc player, DVD player, or HDTV Set Top Box to your TV set is dependent on the model and features of each component. Check the owner’s manual of each component for the location of video and audio inputs and outputs.
The following connection diagrams are offered as suggestions. However, you may need to modify them to accommodate your partic- ular assortment of components and features. For best performance, video and audio cables should be made from coaxial shielded wire.
Before Operating External Video Source
The input mode is changed every time the VID1~VID5 button is pressed as shown below. Connect an external source to the INPUT terminal, then press the VID1~VID5 button as necessary to view the input source (see page 33).
INPUT MODE SELECTION ORDER
(ANTENNA)
Ant A
VID1
ANT
(INPUT)
YPBPR:1
VID1
NOTE: When the TV is set to VIDEO and a video signal is not received from the VIDEO INPUT JACK on the back panel of the TV (i.e., VCR/laserdisc player, etc. is not connected or the video device is OFF), the set will appear to be OFF.
14