JVC HD-52G786, HD-52G886 manual Install the new lamp unit

Page 94

Appendix

5) Install the new lamp unit.

Holding the handle attached to the new lamp unit, slide and push the new lamp straight into the television and back into the lamp housing area. Do not forget to re-tighten the two screws.

Note: If the lamp does not sit securely in the TV (flat in the lamp housing area), it won’t turn on. Make sure the lamp sits securely and flat in the housing area.

WARNING!

Remember it is very important that YOU DO NOT TOUCH THE LAMP SURFACE. Please read the warnings on page 91 again.

Also, replace the lamp with part number TS-CL110U only! The television is designed to work specifically with this lamp. Lamps other than TS-CL110U may cause malfunctions and/or other damage to the television.

NOTICE (for USA)

This product has a High Intensity Discharge (HID) lamp that contains a small amount of mercury. It also contains lead in some components. Disposal of these materials may be regulated in your community due to environmental considerations. For disposal or recycling information, please contact your local authorities, or the Electronics Industries Alliance: http://www.eiae.org

To purchase a replacement lamp kit, please call 1-800-252-5722.

6) Re-install the lamp cover.

Insert the lamp cover in the right concave and close the lamp cover. Because the lamp cover has a role to help prevent the danger of an electrical shock, tighten the screw using your fingers.

Note:

• After installing the new lamp unit, do not forget to reset the lamp timer. See page 66.

94

Image 94

Contents Projection Television Users Guide Important Safety Precautions Risk of Electric Shock Do not OpenImportant Safety Instructions FCC Notice Caring for the Cabinet Caring for the ScreenCooling the inside of the television and the lamp When the power is turned on, the warming up commencesOrder to use the television for a long time Lamp is a consumable itemScreen is made of plastic Television requires a lot of electrical powerILA element characteristics Do not replace the lamp immediately after useTable of Contents OSD Information Digital SetupDigital Button Functions Cable Card InformationQuick Setup Unpacking your TV Component Cables Composite Cables Audio Cables Coaxial CablesVideo Cable AV CompuLink CableHD-52G886 HD-52G786 HD-56G886 Rear Panel DiagramHD-56G786 Side Panel Diagram Front Panel DiagramModels HD-52G886, HD-52G786, HD-56G886, HD-56G786 Quick Setup TV Remote Control HD-52G886 HD-52G786 HD-56G886 HD-56G786Basic Operation Key Feature ButtonsRemote Control Getting StartedConnecting Your Devices Video Cable Component Cables Composite Cables Audio CablesVCR Connection Diagram #2 Connecting to Monitor/Recording Output Terminal Connecting to JVC AV Compu Link AV CompuLink CableConnecting to a Camcorder Connecting to the Surround Amplifier Connecting to an External AmplifierConnecting to an amplifier using your optical output Connecting to a Digital TV Receiver Connecting to an Hdmi Compatible Device Monitor OUT Link Compatible Device Connecting to the computer Looking at the images from a computerTable of signals for each type of computer When a picture is not displayedTo be LanguageInteractive Plug In Menu Auto Clock Set Manual Clock SetAuto Tuner Setup NOW ProgrammingRemote Programming Setting the CATV, VCR and DVD CodesCable Box or Satellite Codes VCR Codes MGADVD Codes SMCCable/Satellite Search Codes Function Search CodesVCR/DVD Search Codes Function Using the Guide Onscreen MenusSelected Option Green Onscreen Menu SystemOnscreen Menu System Selected Option BlueTo Initial Setup Initial Setup Auto Tuner SetupChannel Summary Digital ChannelsContinue to follow these directions for all four spaces Channel Guard Message ChipUnrated Programs Directions to Block Unrated ProgramsUS V-Chip Ratings Setting US V-Chip Ratings Directions to set US V-Chip RatingsMovies Ratings Directions to set Movie Mpaa RatingsCanadian V-Chip Ratings Directions to set Canadian V-Chip RatingsSet Lock Code Auto Demo LanguageDigital Auto Setting Analog SettingClosed Caption Digital Manual Setting Auto Shut Off Noise MutingFront Panel Lock V1 Smart InputVideo Input Label Position Adjustment Power IndicatorTV Speaker Video-1 Monitor OutAudio Out Digital-In Digital-In AudioCenter CH Input Adjust the Picture Settings Picture AdjustPicture Settings Color TemperatureColor Management Digital Noise ClearDynamic Gamma Reset Smart PictureSound Settings Sound AdjustAdjust the Sound Settings Clock/Timers Set ClockOn/Off Timer Lamp Timer Reset Following message will appearMulti Screen Function Button FunctionsTwin Swap IndexFreeze SelectTune PowerNumber Buttons 10Key Pad InputReturn +/TV SoundVideo Status MutingNatural Cinema Sleep Timer Sleep Timer MessageDisplay Volume +Channel + Register the favorite channel FavoriteDelete the favorite channel Aspect Aspect Ratios in PC ModeAspect Ratios Menu BackVCR Buttons TV/CATV Slide SwitchVCR/DVD Slide Switch DVD ButtonsDigital Setup Antenna LevelDigital Sound Aspect RatioCable Card Application Software UpdateLink Auto Play Sub Channel Digital Button FunctionsDigital CH D/A Digital/Analog To watch digital channelsLink Menu ControllerDevice To operate, select a deviceTimer ReservationTimer Edition Timer EditTimer Deletion Cancel the timer recording GuideOSD Information Weak SignalInvalid Signal No ProgramCable Card Information Cable Card ConnectionTroubleshooting Troubleshooting Following are not malfunctionsAppendix Changing the LampReplacement Lamp Kit Lamp MessageRemove the lamp cover How to Replace the LampUnplug the television Remove the lamp unitInstall the new lamp unit Power LED and LAMP/PROGRAM LED blink rapidly simultaneously Power LED blinksPower LED and LAMP/PROGRAM LED blink alternately LAMP/PROGRAM LED blinksPage Specifications Specifications subject to change without notice