AUX (audio cable not included) .(See 9)
This 3.5mm socket allows you to connect other audio equipment to your system.
1.Press y to on, then the source selector to select AUX.
= Display shows: AUX and PHILIPS scrolls
2.Use an audio cable to connect the AUX socket to the LINE OUT/headphone socket on your external equipment.
3.To avoid noise distortion, turn down the volume on your external equipment.
4.To adjust the sound and volume, use the sound controls on your external equipment and the AZ3068.
Cassette recorder
Cassette playback
1.Press y to on, then the source selector to select TAPE.
=Display shows 
throughout tape operation.
2.Insert a cassette and close the door.
3.Press PLAY 1 to start playback.
4.To pause, press PAUSE ;;. Press PAUSE ; again to resume.
5.Press SEARCH 5/6 to fast wind the tape.
6.To stop the tape, press STOP•OPEN 9/.
Helpful Hints:
-During playback, the keys are automatically released at the end of a tape and the set is switched off (unless PAUSE mode ; has been activated.)
-During fast forwarding/rewinding, the keys will not be released at the end of a tape. To switch off the set, make sure the cassette keys are also released.
GENERAL INFORMATION ON RECORDING
•Recording is permissible insofar as copyright or. other rights of third parties are not infringed.
•For recording, use only NORMAL type cassettes (IEC type I) on which the tabs have not yet been broken. This deck is not suited for recording on CHROME (IEC II) or METAL (IEC IV) type cassettes.
•The best recording level is set automatically. Altering the VOLUME or BASS controls will not affect the recording.
•To protect a tape from accidental erasure, break out the tabs. If you wish to record again, cover the tabs with a piece of adhesive tape.
Recording from the CD Player
1Select CD source.
2Insert a CD and if desired, program track num- bers.
3Press STOP•OPEN 9// to open the cassette holder. Insert a blank tape and close the deck.
4Press RECORD 0 to start recording.
5Press 2; to start CD playback.
6For brief interruptions press PAUSE ;. To resume recording, press PAUSE ; again.
7To stop recording, press STOP•OPEN 9//.
Recording from the Radio
1Tune to the desired radio station (see Tuning to radio stations).
2Follows steps 3, 4, 6,7 under Recording from the CD Player.
MAINTENANCE & SAFETY (See 0)
CD player and disc handling
•If the CD player cannot read CDs correctly, use a cleaning CD to clean the lens before taking the set to repair.
•The lens of the CD player should never be touched!
•Sudden changes in the surrounding temperature can cause condensation on the lens of your CD player. Playing a CD is then not possible. Do not attempt to clean the lens but leave the set in a warm environment until the moisture evaporates.
•Always close the CD door to avoid dust on the lens.
•To clean the CD, wipe in a straight line from the centre towards the edge using a soft, lint-free cloth. Do not use cleaning agents as they may damage the disc.
•Never write on a CD or attach any stickers to it.
Tape deck maintenance
To ensure quality recording and playback of the tape deck, clean parts A, B and C as shown, once a month. Use a cotton bud slightly moistened with alco- hol or a special head cleaning fluid to clean the deck.
1Open the cassette door.
2Press PLAY 1 and clean the roller C.
3Press PAUSE ; and clean the heads A, and the capstan B.
4After cleaning, press STOP/OPEN 9/.
Safety Information
•Place the set on a hard, flat and stable surface so that the system does not tilt.
•Where the MAINS plug or an appliance coupler is used as the disconnet device, the disconnet device shall remain readily operable.
•Do not expose the set, batteries, CDs to humidity, rain, sand or excessive heat caused by heating equipment or direct sunlight.
•The apparatus shall not be exposed to dripping or splashing.
•Adequate ventilation with a minimum gap of 6 inches between the ventilation holes and surround- ing surfaces is necessary to prevent heat build-up.
•The ventilation should not be impeded by covering the ventilation openings with items, such as news- papers, table-cloths, curtains, etc..
•No objects filled with liquids, such as vases, shall be placed on the apparatus.
•No naked flame sources, such as lighted candles, should be placed on the apparatus.
•The mechanical parts of the set contain self-lubricating bearings and must not be oiled or lubricated.
•To clean the set, use a dry cloth. Do not use any cleaning agents containing alcohol, ammonia, ben- zene or abrasives as these may harm the housing.
•Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like.
CAUTIONS:
-Visible and invisible laser radiation. If the cover is open, do not look at the beam.
-High voltage! Do not open.You run the risk of getting an electric shock. The machine does not contain any user-serviceable parts.
-Modification of the product could result in haz- ardous radiation of EMC or other unsafe opera- tion.
