Philips DVP4000/78 user manual Getting Started, Using the Remote Control, Setting up the TV

Page 11

Step 1: Using the Remote Control

1 2

CR 2025

L

I

THIUM

1Pull out the plastic protective sheet.

2To replace battery (Lithium CR2025);

pull out the battery compartment

replace a new battery and fully insert the battery compartment back to the original position.

3Close the cover.

Using the Remote Control to operate the Player

1Aim the Remote Control directly at the remote

sensor (iR) on the front

Y

ON IR

PLA

 

 

PA

 

 

 

panel.

 

 

 

2Do not put any objects between the Remote Control and the DVD Player while operating the DVD Player.

VOLUME

CAUTION!

Remove batteries if they are exhausted or if the Remote Control is not being used for a long time.

Batteries contain chemical substances, so they should be

disposed properly.

Getting Started

Step 2: Setting up the TV

IMPORTANT!

Make sure you have completed all the necessary connections. (See page 6-7 “Connecting TV”).

1Turn on the TV and set to the correct video-in channel. You should see the DVD background screen on the TV.

2Usually these channels are between the lowest and highest channels and may be called FRONT,A/V IN, or VIDEO. See your TV manual for more details.

Or, you may go to channel 1 on your TV, then press the Channel down button repeatedly until you see the Video In channel.

Or, the TV Remote Control may have a button or switch that chooses different video modes.

Or, set the TV to channel 3 or 4 if you are using an RF modulator.

3If you are using external equipment, (eg. audio system or receiver), turn it on and select the appropriate input source for the DVD Player output. Refer to the equipment owner’s manual for detail.

To deactivate Progressive manually

When the distorted picture still appears on the TV, it may be due to the connected TV does not accept progressive signals, and progressive is set by mistake. You must reset the unit to interlace format.

1Turn off your TV progressive scan mode or turn on to interlaced mode (refer to your TV user manual.)

2Press / (OPEN/CLOSE) on the DVD player to open the disc tray.

3Press numeric keypad ‘1’ on the

remote control for few seconds.

The DVD blue background screen will appear on the TV.

11

E n g l i s h

3139 246 14692

01-28 DVP4000_7821118/01/2005, 2:54 AM

Image 11
Contents 3139 246 Need help fast?Laser Laser safetyGeneral Information Environmental InformationEnglish Español Português IndexContents Introduction Supplied accessoriesCare and safety information Connections Using Composite Video jacks CvbsUsing Component Video jacks Y Pb Pr Using an accessory RF modulator Connecting the power cordHelpful Hint Receiver has a PCM, Dolby Digital, or MPEG2 decoderFront and Rear Panels Functional OverviewRemote Control Getting Started Using the Remote ControlSetting up the TV Using the Remote Control to operate the PlayerPress System Menu Setting the TV DisplaySelecting the color system that corresponds to your TV Press 2 to select LANGUAGE, then press OK Setting language preferenceSetting the OSD Language Setting the Audio, Subtitle and DVD menu languageYour DVD Player will play Disc OperationsPlayable Discs Region CodesFor VCD with Playback Control PBC feature version 2.0 only Using the Disc MenuTo select a playback feature or item To access or exit from the menuPlay B Basic playback controlsChanging the Audio Language Special DVD featuresSelecting a title Camera AnglePlaying MP3/JPEG Picture CD Language DVD Setup Menu OptionsVideo Setup OFF Audio SetupProgressive turning on/off Lpcm Output Digital OutputALL PCMPress 2 repeatedly to select Rating Press OK to confirm Night Mode turning on/offRating New four-digit password will now take effect Changing the Password Setting the RatingWhen doing this for the first time, key in ‘0000’ Enter the new four-digit passwordRating explanations Restoring to original settingsAudio Format SpecificationsProblem Solution TroubleshootingTroubleshooting Glossary