Philips MCD708/58 user manual Connecting FM/MW antennas, Using an accessory RF modulator

Page 13

Connections

Using an accessory RF modulator

IMPORTANT!

–If your TV only has a single Antenna In jack (labeled as 75 ohm or RF In), you will need an RF modulator in order to view DVD playback on the TV. See your electronics retailer or contact Philips for details on RF modulator availability and operations.

Step 5: Connecting FM/MW antennas

fix the claw into

the slot

1 MW antenna

English

ANT IN

RF coaxial cable to TV

2

INT IN TO TV VIDEO	AUDIO IN
IN	R	L

CH3 CH4

3

1

1Use the composite video cable (yellow) to connect the DVD systemÕs VIDEO OUT jack to the video input jack on the RF modulator.

2Use an RF coaxial cable (not supplied) to

connect ANTENNA OUT or TO TV jack on the RF modulator to the Antenna IN jack on the TV.

3Connect the Antenna or Cable TV service signal to the ANTENNA IN or RF IN jack on the RF modulator. (It may have been connected to your TV previously. Disconnect it from the TV.)

2FM

antenna

SUB WOOFER

1Connect the supplied MW loop antenna to the

MW jack. Place the MW loop antenna on a shelf or attach to a stand or wall.

2Connect the supplied FM antenna to the FM (75 Ω) jack. Extend the FM antenna and fix its end to the wall.

For better FM stereo reception, connect an external FM antenna (not supplied).

Note:

–Adjust the position of the antennas for optimal reception.

–Position the antennas as far as possible from your TV,VCR or other radiation source to prevent unwanted interference.

13

Image 13

Contents DVD Micro Theatre Garancia MinőségtanúsításProhibited Manufactured under license from Dolby LaboratoriesWindows Media is a trademark of Microsoft Corporation Language Code 149 115184 Magyar Slovensky Č e s k y Polski Русский EnglishContents Other Functions System Menu Options31-32 Supplied accessories FeaturesInstallation General InformationDisposal of your old product MaintenanceStep ConnectionsSpeaker Type plate is located at the bottom of the systemConnecting TV Connecting the control cableUsing Scart jack Using Composite Video jackUsing Component Video jacks Y Pb Pr Using an accessory RF modulator Connecting FM/MW antennasUse an RF coaxial cable not supplied to Additional Connecting additional equipment Connecting the power cordFunctional Overview DVD player and power amplifierSystem disc mode only Remote controlDisc Menu disc mode only Numeric Keypad@ TU +/- à / á # Volume +$ CH +/- ¡ ∞ A-BSetting up the TV Inserting batteries into the Remote ControlUsing the Remote Control to operate Player Getting StartedTo deactivate Progressive manually Setting the OSD Language Setting language preferenceSetting the Audio, Subtitle and Disc Menu language To exit from the menuBasic Operations Playable Discs Disc OperationsRegion Codes Playing discsBasic playback controls Using the Disc MenuSlow Motion DVD/VCD English Repeat A-B DVD/VCD/CD/MP3/DivXProgram not for Picture CD Forward/Reverse Searching DVD/VCD DivX/CD/MP3/WMAPlaying MP3/WMA/JPEG Picture Special disc featuresPlaying MP3/WMA disc Playing Jpeg Picture CD Special Jpeg featuresPreview function Jpeg Zoom picture JpegPlayback with multi-angles Jpeg Playing a DivX discSystem Menu Options General SetupBasic operations Dolby Digital Setup Audio SetupDivxr VOD registration code Dual MonoNight Mode Video SetupEnglish 3D Processing Video OutputColor Setting TV ModePreference ParentalRating explanations DefaultNC-17 Other Functions Setting the RDS clockRadio Reception Setting sleep/wake-up timer Setting the clockSleep timer setting Wake-up timer settingSpecifications Problem TroubleshootingSolution Check if the AC power cord is properly connectedTune in to the correct frequency Connect the antennas Troubleshooting Glossary